manualshive.com logo in svg

Kyocera TASKalfa 250ci, Service Manual

The Kyocera TASKalfa 250ci is a high-performance multifunctional printer equipped with advanced features. This versatile device comes with an easy-to-understand Operation Manual, available for free download from our website. Get the most out of your printer by referring to the comprehensive manual for efficient and hassle-free operation.

Share
Download
background image

7

A4

Letter

B5

19

19

16

16

15

19

19

20

21

21

21

21

22

22

A4

Letter

B5

B5

Letter

A4

20

A4
LT
B5

18

15

4.

サイズ指示爪 (18) が使用する用紙サイズを示すように、前後の横幅サイズ板 (16) の上爪 (19)、

下爪 (20) を上溝 (21)、下溝 (22) に差し込み、ビス

(17)1 本で固定する。
前後の上爪 (19) を上溝 (21) の差し込む位置で用紙サイズを確認する。
前側の上溝 (21) の位置：手前（A4）、中央（Letter）

、奥（B5）

後側の上溝 (21) の位置：手前（B5）、中央（Letter）

、奥（A4）

5.

前後各 2 枚のスライド板 (15) を、横幅サイズ板 (16) に当たるまで外側にずらす。

4.

Führen Sie die oberen Laschen (19) und die unteren Laschen (20) der vorderen und hinteren Quergrößen-Einsteller (16) jeweils in die oberen Schlitze 
(21) und unteren Schlitze (22), so daß die Größenanzeiger (18) auf die zu benutzende Papiergröße zeigen. Sichern Sie die Quergrößen-Einsteller mit 
jeweils einer Schraube (17).
Die Papiergröße an der Stelle überprüfen, wo vorderen und hinteren oberen Laschen (19) in den oberen Schlitzen (21) sitzen.
Positionen der oberen Schlitze (21) auf der Vorderseite: vorne (A4), Mitte (Letter), hinten (B5)
Positionen der oberen Schlitze (21) auf der Rückseite: Vorne (B5), Mitte (Letter), Hinten (A4)

5.

Bewegen Sie die vorderen und hinteren Schieber (15) (zwei an jedem Punkt) nach außen, bis sie mit den Quergrößen-Einstellern (16) in Kontakt 
kommen.

4.

Inserte las lengüetas superiores (19) y las lengüetas inferiores (20) de los reguladores de tamaño laterales frontales y traseros (16) en las ranuras 
superiores (21) y las ranuras inferiores (22) respectivamente de modo que los indicadores de tamaño (18) apunten al tamaño de papel a ser usado. 
Asegure los reguladores de tamaño laterales usando el tornillo (17) para cada uno.
Compruebe el tamaño de papel en la posición con las lengüetas frontales y traseras superiores (19) insertadas en las ranuras superiores (21).
Posiciones de las ranuras superiores (21) en el lado delantero: Adelante (A4), medio (carta), atrás (B5)
Posiciones de las ranuras superiores (21) en el lado trasero: Adelante (B5), medio (Carta), atrás (A4)

5.

Mueva los graduadores frontales y traseros (15) (dos en cada punto) hacia fuera hasta que hagan contacto con los reguladores de tamaño laterales (16).

4.

Insérer les pattes supérieures (19) et inférieures (20) des dispositifs de réglage du format latéral avant et arrière (16), dans les fentes supérieures (21) 
et inférieures (22) respectivement, de façon à ce que les indicateurs de format (18) pointeent à la taille du papier à utiliser. Fixer les dispositifs de 
réglage du format latéral à l’aide de leur vis (17).
Vérifier le format du papier en position avec les pattes supérieures avant et arrière (19) insérées dans les fentes supérieures (21).
Positions des fentes supérieures (21) sur le côté avant: Avant (A4), milieu (Lettre), arrière (B5)
Positions des fentes supérieures (21) sur le côté arrière: Avant (B5), milieu (Lettre), arrière (A4)

5.

Déplacer les curseurs avant et arrière (15), (deux à chaque endroit), vers l’extérieur jusqu’à ce qu’ils entrent en contact avec les dispositifs de réglage 
du format latéral (16).

4.

Insert the upper tabs (19) and lower tabs (20) of the front and rear lateral size adjusters (16) into the upper slots (21) and lower slots (22) respectively 
such that the size indicators (18) point to the size of paper to be used. Secure the lateral size adjusters using the screw (17) for each.
Check the paper size at the position with the front and rear upper tabs (19) inserted into the upper slots (21). 
Upper slots (21) positions on the front side: Front (A4), middle (Letter), rear (B5)
Upper slots (21) positions on the rear side: Front (B5), middle (Letter), rear (A4)

5.

Move the front and rear sliders (15) (two at each point) outward until they make contact with the lateral size adjusters (16).

4.

Inserire le linguette superiori (19) e le linguette inferiori (20) dei regolatori della misura laterale anteriori e posteriori (16) nelle scanalature superiori 
(21) e nelle scanalature inferiori (22) rispettivamente, in modo tale che gli indicatori della misura (18) puntino alla dimensione della carta da utilizzare. 
Fissare i regolatori della misura laterale utilizzando la vite (17) per ciascuno di essi. 
Controllare il formato della carta alla posizione delle linguette superiori anteriori e posteriori (19) inserite nelle scanalature superiori (21).
Posizioni delle scanalature superiori (21) sul lato anteriore: anteriore (A4), centrale (Letter), posteriore (B5)
Posizioni delle scanalature superiori (21) sul lato posteriore: Anteriore (B5), centrale (Lettera), posteriore (A4)

5.

Spostare verso l’esterno gli scivoli anteriori e posteriori (15) (due in ciascun punto) fino a quando non vengano a contatto con i regolatori della misura 
laterale (16). 

4. 将前后横向尺寸板 (16) 的上卡爪 (19)、下卡爪 (20) 分别插入上槽 (21) 和下槽 (22)，再用 1 个螺丝 (17) 固定，让尺寸指示爪 (18) 表示所使用的复印

纸尺寸。
检查前后上卡爪 (19) 插入上槽 (21) 位置时的纸张尺寸。
前面的上槽 (21) 的位置∶前面 (A4)、中央 (Letter)、里侧 (B5)
后面的上槽 (21) 的位置∶前面 (B5)、中央 (Letter)、里侧 (A4)

5. 向外移动前后各 2 张滑板 (15)，直到碰到横向尺寸板 (16) 为止。

Summary of Contents for TASKalfa 250ci



















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 250ci

Samsung M267x series Quick Installation Manual preview
M267x series
Brand: Samsung Pages: 2
Samsung CLX-6220FX Quick Install Manual preview
CLX-6220FX
Brand: Samsung Pages: 2
Samsung CLX-3305FW Manual Del Usuario preview
CLX-3305FW
Brand: Samsung Pages: 341
Samsung CLX-3170 Quick Install Manual preview
CLX-3170
Brand: Samsung Pages: 8
Samsung CLX2160N - Color Laser - All-in-One Manual Del Usuario preview
CLX2160N - Color Laser - All-in-One
Brand: Samsung Pages: 118
Samsung CLX 3160FN - Color Laser - All-in-One Manual Del Usuario preview
CLX 3160FN - Color Laser - All-in-One
Brand: Samsung Pages: 142
Samsung CLP-770ND - Color Laser Printer Quick Install Manual preview
CLP-770ND - Color Laser Printer
Brand: Samsung Pages: 2
Samsung CLP 610ND - Color Laser Printer Manual Del Usuario preview
CLP 610ND - Color Laser Printer
Brand: Samsung Pages: 114
Samsung CLP 500 Instructions Manual preview
CLP 500
Brand: Samsung Pages: 6
Samsung CLP 500 Paigaldusjuhend preview
CLP 500
Brand: Samsung Pages: 15
Samsung CLP 600N - Color Laser Printer User Manual preview
CLP 600N - Color Laser Printer
Brand: Samsung Pages: 227
Samsung CLP 600N - Color Laser Printer Manual Del Usuario preview
CLP 600N - Color Laser Printer
Brand: Samsung Pages: 118
Samsung CLP 300N - Network-ready Color Laser Printer Manual De Usuario preview
CLP 300N - Network-ready Color Laser Printer
Brand: Samsung Pages: 94
Samsung CJX-2000FW Series Quick Install Manual preview
CJX-2000FW Series
Brand: Samsung Pages: 2
Samsung 4116 - SCX B/W Laser User Manual preview
4116 - SCX B/W Laser
Brand: Samsung Pages: 205
Samsung 3561ND - B/W Laser Printer User Manual preview
3561ND - B/W Laser Printer
Brand: Samsung Pages: 252
Samsung 3561ND - B/W Laser Printer Manual Del Usuario preview
3561ND - B/W Laser Printer
Brand: Samsung Pages: 127
Samsung CLX-3305FN User Manual preview
CLX-3305FN
Brand: Samsung Pages: 314

Brands by name

Popular brands

Load more brands