manualshive.com logo in svg

Kyocera TASKalfa 250ci, Service Manual

The Kyocera TASKalfa 250ci is a high-performance multifunctional printer equipped with advanced features. This versatile device comes with an easy-to-understand Operation Manual, available for free download from our website. Get the most out of your printer by referring to the comprehensive manual for efficient and hassle-free operation.

Share
Download
background image

8

B5

A4

24 (G)

26

26

25

25

27

27

23 (F)

23 (F)

24 (G)

24 (G)

6.

各ビス (24)1 本を外し、縦幅サイズ板 (23) を取り外す。

（センチ仕様のみ）

7.

用紙サイズに応じて、

縦幅サイズ板 (23) のピン穴 (25) を A4 ピン (26) または B5 ピン (27) に合わ

せて取り付け、

ビス (24)1 本で固定する。

インチ仕様では、用紙サイズに応じて、

縦幅サイズ板 (F) のピン穴 (25) を A4 ピン (26) または B5

ピン (27) に合わせて取り付け、

ビス + ナベ M3×8 タッピング (G)1 本で固定する。

8.

ペーパーフィーダのカセットおよび MFP 本
体の下段カセットを元に戻す。

9.

MFP 本体の電源プラグをコンセントに差し込
み、主電源スイッチを ON にする。

メンテナンスモード U208 でペーパーフィーダ
にセットする用紙のサイズ（B5 ／ A4 ／ Letter）
を設定する。

6.

Remove the screw (24) and remove the longitudinal size adjusters (23). (metric specifications only)

7.

Depending on the paper size, align either the A4 pins (26) or the B5 pins (27) with the pin holes 
(25) in the longitudinal size adjusters (23), fit the adjusters and secure each of them with a screw 
(24). 
For inch specifications, align either the A4 pins (26) or the B5 pins (27) with the pin holes (25) in 
the longitudinal size adjusters (F), fit the adjusters and secure each of them with a round pan-head 
M3 x 8 tapping screw (G).

8.

Return the paper feeder cassette and the 
lower cassette in the MFP to their original 
positions.

9.

Run maintenance item U208 and set the 
paper size for the paper feeder (B5/A4/
Letter).

6.

Déposer la vis (24) et déposer les dispositifs de réglage du format longitudinal (23). (spécifications 
métriques seulement)

7.

Selon le format du papier, aligner les broches A4 (26) ou B5 (27) avec les trous de broche (25) dans 
les dispositifs de réglage du format longitudinal (23), ajuster les dispositifs de réglage et les fixer 
chacun avec une vis (24).
Pour les spécifications en pouces, aligner les broches A4 (26) ou B5 (27) avec les trous de broche 
(25) des dispositifs de réglage du format longitudinal (F), ajuster les dispositifs de réglage et les 
fixer chacun à l’aide d'une vis autotaraudeuse à tête cruciforme ronde M3 × 8 (G).

8.

Ramener la cassette du bureau papier et la 
cassette inférieure dans leur position 
d'origine dans le MFP.

9.

Exécuter l’élément d’entretien U208 et régler 
la taille du papier pour le bureau papier (B5/
A4/Letter).

6.

Quite el tornillo (24) y desmonte los reguladores de tamaño longitudinal (23). (sólo especificaciones 
métricas)

7.

Dependiendo del tamaño del papel, alinee las clavijas A4 (26) o las clavijas B5 (27) con los orificios 
para las clavijas (25) en los reguladores de tamaño longitudinal (23), inserte los reguladores y 
asegúrelos con un tornillo (24).
En el caso de especificaciones de pulgadas, alinee las clavijas A4 (26) o las clavijas B5 (27) con los 
orificios para las clavijas (25) en los reguladores de tamaño longitudinal (F), encaje los reguladores 
y asegúrelos con un tornillo de roscado de cabeza redonda plana M3 x 8 (G).

8.

Vuelva a colocar el cajón del alimentador de 
papel y el cajón inferior del MFP en sus 
posiciones originales.

9.

Haga el ítem de mantenimiento U208 y 
configure el tamaño de papel para el 
alimentador de papel (B5/A4/Letter). 

6.

Die Schraube (24) entfernen und die Längsgrößen-Einsteller (23) abnehmen. (nur metrische 
Spezifikationen)

7.

Je nach Papiergröße entweder die A4-Stifte (26) oder die B5-Stifte (27) auf die Stiftlöcher (25) in den 
Längsgrößen-Einstellern (23) ausrichten, die Einsteller einsetzen und jeden mit einer Schraube (24) 
sichern.
Richten Sie die Stiftlöcher (25) im linken und rechten Längsgrößen-Einsteller (F) für Zollspezifikationen 
auf die A4-Stifte (26) oder B5-Stifte (27) aus, abhängig von der zu verwendenden Papiergröße. 
Sichern Sie die Einsteller mit jeweils einer Kreuzschlitz- Rundkopf-Schneidschraube M3 × 8 (G).

8.

Die Papierlade des Papiereinzug und die 
untere Papierlade im MFP wieder wie 
ursprünglich einsetzen.

9.

Führen Sie Wartungspunkt U208 aus und 
stellen Sie die Papiergröße für den 
Papiereinzug (B5/A4/Letter) ein.

6.

Rimuovere la vite (24) e quindi rimuovere i regolatori della misura longitudinale (23). (solo specifiche 
metriche)

7.

 Dipendentemente dal formato della carta, allineare i perni A4 (26) o i perni B5 (27) con i fori dei perni 
(25) nei regolatori della misura longitudinale (23), adattare i regolatori e fissare ciascuno di loro con 
una vite (24).
Per le specificazioni in pollici, allineare i perni A4 (26) o i perni per B5 (27) con i fori dei perni (25) nei 
regolatori della misura longitudinale (F), adattare i regolatori e fissare ciascuno di loro con una vite 
filettante a testa piana M3 x 8 (G).

8.

Riportare la cassetta dell’unità di 
alimentazione della carta e la cassetta 
inferiore dell’MFP alle loro posizioni originali. 

9.

Eseguire l’opzione di manutenzione U208 ed 
impostare la dimensione della carta della 
relativa unità di alimentazione (B5/A4/
Letter).

6. 拆下螺丝 (24)，然后拆下纵向尺寸板 (23)。( 仅适用于厘米尺寸的产品 )
7. 根据纸张尺寸，将 A4 插销 (26) 和 B5 插销 (27) 与纵向尺寸板 (23) 上的插销孔 (25) 对齐，装上

纵向尺寸板，并用螺丝 (24) 将每个尺寸板都固定。
对于英制规格的机器，将 A4 插销 (26) 和 B5 插销 (27) 与纵向尺寸板 (F) 上的插销孔 (25) 对
齐，装上纵向尺寸板，并用圆盘头

M3

×

8

自攻螺丝 (G) 将每个尺寸板都固定。

8. 将供纸工作台供纸盒和 MFP 的下部供纸盒装

回至原来的位置。

9. 将 MFP 主机上的电源插头插入电源插座中，打

开主电源开关。

使用维修模式 U208 设定供纸工作台所使用的复印
纸尺寸 (B5/A4/Letter)。

Summary of Contents for TASKalfa 250ci



















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 250ci

Xerox Phaser 6120 Service Manual preview
Phaser 6120
Brand: Xerox Pages: 15
Xerox Phaser 6120 Voluntary Product Accessibility Template preview
Phaser 6120
Brand: Xerox Pages: 9
Xerox DocuPrint 180 NPS Series Installation Planning Manual preview
DocuPrint 180 NPS Series
Brand: Xerox Pages: 172
Xerox Phaser 4500 Voluntary Product Accessibility Template preview
Phaser 4500
Brand: Xerox Pages: 11
Xerox Phaser 7750 Quick Reference Manual preview
Phaser 7750
Brand: Xerox Pages: 8
Xerox Phaser 7300 Features Manual preview
Phaser 7300
Brand: Xerox Pages: 40
Xerox ColorQube 8700 Reference Manual preview
ColorQube 8700
Brand: Xerox Pages: 28
Xerox Color C75 Press User Manual preview
Color C75 Press
Brand: Xerox Pages: 340
Xerox EC8036 User Manual preview
EC8036
Brand: Xerox Pages: 370
Xerox DocuPrint N3225 User Manual preview
DocuPrint N3225
Brand: Xerox Pages: 169
Xerox D110 Specification preview
D110
Brand: Xerox Pages: 8
Xerox DocuPrint 65 Quick Start Manual preview
DocuPrint 65
Brand: Xerox Pages: 16
Xerox Phaser 7400 Setup Manual preview
Phaser 7400
Brand: Xerox Pages: 2
Xerox Phaser 7400 User Manual preview
Phaser 7400
Brand: Xerox Pages: 196
Xerox Nuvera 120 EA Specification Sheet preview
Nuvera 120 EA
Brand: Xerox Pages: 2
Xerox DocuColor 2060 Administration Manual preview
DocuColor 2060
Brand: Xerox Pages: 108
Xerox PHASER 3500 Options Manual preview
PHASER 3500
Brand: Xerox Pages: 2
Canon Pixma iP2580 Quick Start Manual preview
Pixma iP2580
Brand: Canon Pages: 12

Brands by name

Popular brands

Load more brands