manualshive.com logo in svg

Kyocera TASKalfa 250ci, Service Manual

The Kyocera TASKalfa 250ci is a high-performance multifunctional printer equipped with advanced features. This versatile device comes with an easy-to-understand Operation Manual, available for free download from our website. Get the most out of your printer by referring to the comprehensive manual for efficient and hassle-free operation.

Share
Download
background image

2

G

G

H

H

Procedure

Be sure to turn the MFP main power switch off 
and disconnect the MFP power plug from the 
wall outlet before starting to install the mailbox.

Before installing the finisher, carry out the 
following procedure.

[Carry out steps 1 when installing the 

mailbox to a full-color machine.]

1.

Fit the two plate feet V (H) and secure them 
using two M4 x 10TP screws (G) for each.
Install the finisher referring to the installation 
guide for finisher.

When using a full-color machine: Proceed to 
step 4 on page 4

Procédure

Veiller à bien mettre l’interrupteur principal du 
MFP sur la position d’arrêt et à débrancher la 
fiche d’alimentation du MFP de la prise murale 
avant d’entreprendre l’installation de la boîte à 
lettres.

Avant d’installer le retoucheur, effectuer la 
procédure suivante.

[Effectuer les étapes 1 lorsqu’on 

installe la boîte à lettres sur une 

machine entièrement en couleurs.]

1.

Insérer les deux pieds de plaques V (H) et les fixer 

à l'aide de deux vis M4 x 10TP (G) pour chaque 

pièce.

Installer le retoucheur en se reportant au guide 

d’installation du retoucheur.

Lors de l’utilisation de la machine entièrement en 

couleurs: passer à l’étape 4 de la page 4

Procedimiento

Asegúrese de apagar el MFP con el interruptor 
principal y de desconectar la clavija de 
alimentación del MFP de la toma de corriente 
de la pared antes de empezar a instalar el 
buzón de correo.

Antes de instalar el finalizador, realice el 
siguiente procedimiento.

[Realice los pasos 1 cuando instale el 

buzón de correo en una máquina a todo 

color.]

1.

Coloque las dos patas de placa V (H) y asegúrelas 

por medio de dos tornillos M4 x 10TP (G) para 

cada una.

Instale el finalizador consultando la guía de 

instalación para el finalizador.

Cuando utilice una máquina a todo color: Vaya al 

paso 4 de la página 4

Verfahren

Schalten Sie vor der Installation der Mailbox 
unbedingt den Hauptschalter des MFP aus, und 
ziehen Sie den Netzstecker aus der 
Netzsteckdose.

Bevor Sie den Finisher installieren, führen Sie 
das folgende Verfahren aus.

[Führen Sie die Schritte 1 aus, wenn Sie 

die Mailbox an einer 

Vollfarbenmaschine anbringen.]

1.

Bringen Sie die beiden Plattenfüße V (H) an, und 

befestigen Sie sie jeweils mit zwei M4 x 10TP 

Schrauben (G).

Installieren Sie den Finisher gemäß der 

Installationsanleitung des Finishers.

Bei Verwendung eines Vollfarbenkopierers: Gehen 

Sie zum Schritt 4 auf Seite 4 weiter

Procedura

Non mancare di spegnere l’MFP utilizzando 
l’interruttore principale di alimentazione e 
scollegare la spina del cavo di alimentazione 
dell’MFP dalla presa della rete elettrica, prima di 
cominciare a installare la casella postale.

Prima di installare il finitore, eseguire le seguenti 
procedure.

[Eseguire il procedimento dei passi da 1 

quando si installa la casella postale su 

una macchina a colori.]

1.

Inserire i due piedini della piastra V (H) e fissare 

ciascuno di essi utilizzando due viti M4 x 10TP (G).

Installare il finitore seguendo le istruzioni della 

guida all’installazione del finitore.

IN caso si utilizzi un macchinario a colori: 
Procedere con il punto 4 a pagina 4

[ 取付手順 ]

メールボックスを取り付ける際は、必ず MFP 本
体の主電源スイッチを OFF にし、電源プラグを
外して作業をおこなう。

フィニッシャの設置を行う前に、次の手順を行
う。

[ 手順 1 はフルカラー機に取り付ける場合 ]

1. プレートフット V(H) を 2 箇所取り付け、ビ

ス M4 × 10TP(G) 各 2 本で固定する。
フィニッシャの設置手順書を参照して、フィ
ニッシャの設置を行う。

フルカラー機の場合：4 ページ手順 4 へ進む。

[

安装步骤

]

安装邮箱时，必须关闭

MFP

主机上的主电源开

关，并拔下主装置的电源插头后进行安装。

安装装订器之前，先按以下步骤进行操作。

[

在全彩色机上安装时的步骤

1]

1.

将底板

V (H)

安装在

2

处后，分别用

2

个螺丝

M4 

×

 10TP (G)

进行固定。

参照装订器安装手册，进行安装装订器。

使用全彩色机时：进行第 4 页上的第 4 步

Summary of Contents for TASKalfa 250ci



















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 250ci

Canon Color imageCLASS MF8580Cdw User Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon ImageCLASS 2300 Setup Sheet preview
ImageCLASS 2300
Brand: Canon Pages: 8
Canon Color imageCLASS MF8580Cdw Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon Color imageCLASS 8180c Facsimile Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 95
Canon GP200 Installation Instructions preview
GP200
Brand: Canon Pages: 4
Canon CFX-B380 IF Parts List preview
CFX-B380 IF
Brand: Canon Pages: 49
Canon ImageCLASS 2300 Basic Manual preview
ImageCLASS 2300
Brand: Canon Pages: 156
Canon FaxPhone L90 Reference Manual preview
FaxPhone L90
Brand: Canon Pages: 193
QMS 3225 Tray Module Installation Manual preview
3225
Brand: QMS Pages: 24
Canon imageCLASS D1120 User Manual preview
imageCLASS D1120
Brand: Canon Pages: 36
Canon ImageCLASS 2300 Remote Ui Manual preview
ImageCLASS 2300
Brand: Canon Pages: 44
Canon FAXPHONE L75 Software User'S Manual preview
FAXPHONE L75
Brand: Canon Pages: 66
Samsung SCX-4300 - SCX 4300 B/W Laser Installation Instructions preview
SCX-4300 - SCX 4300 B/W Laser
Brand: Samsung Pages: 4
Samsung ML-2240 - 23 Ppm Mono Laser Printer Manual preview
ML-2240 - 23 Ppm Mono Laser Printer
Brand: Samsung Pages: 16
Samsung ML 2510 - B/W Laser Printer User Manual preview
ML 2510 - B/W Laser Printer
Brand: Samsung Pages: 170
Samsung CLX-3185FN Manual Del Usuario preview
CLX-3185FN
Brand: Samsung Pages: 165
Xerox 770 System Administration Manual preview
770
Brand: Xerox Pages: 114
ABLE AP1200 Programmer'S Manual preview
AP1200
Brand: ABLE Pages: 26

Brands by name

Popular brands

Load more brands