Kyocera TASKalfa 3051ci Service Manual Download

Page: 217 / 317

2L6/2N6/2N5/2N4

1-4-216

(4) The background is colored.

1. Table scanning

Print example

Defective part

Check description

Corrective Action

Original document

1. Check if the background

density of the original
document is too dense.

2. Check if the original

document is floated during
scanning.

1. If the background density of the original

document is too dense, perform automatic
background adjustment.Or, adjust density
with background adjustment.

2. If the original document is floated during

scanning, press down the original
document.

Adjustment of the
scanner

Check the automatic adjustment
of the scanner.

Perform maintenance mode U411,
table(Chart1)_All.
(see page 1-3-173)

Contact glass

Check whether the contact glass
is dirty.

If the contact glass is dirty, clean the contact
glass, and the bottom part of the shading plate.

Contact glass assy Check the location the contact

glass is mounted.

Re-mount the contact glass if it is hanged off.

Home position
sensor

Check the location the home
position sensor is mounted.

Re-mount the home position sensor if it is
hanged off.

FFC cable CCD

Check the FFC cable between
the CCD sensor and ISC PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

FFC cable LED

Check the FFC cable between
the LED PWB and ISC PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

Lamp unit

Check the location the lamp unit
is mounted.

Re-mount the lamp unit if it is hanged off.

LED PWB

Check that the LED is lit.

If the LED is not lit, replace the LED PWB and

perform U411.

ISC PWB

The ISC PWB is defective.

replace the ISC PWB and perform U411.

(see page 1-3-173)

CCD PWB

The CCD PWB is defective.

Replace the ISU and perform U411.

(see page 1-3-173)

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands

Kyocera TASKalfa 3051ci, Service Manual

Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands