Kyocera TASKalfa 3051ci Service Manual Download

Page: 228 / 317

2L6/2N6/2N5/2N4

1-4-227

2. DP-scanning first (front) page

3. DP-scanning second (back) page (with a dual scan DP installed)

Defective part

Check description

Corrective Action

Original document

Check whether the original

document is dirty.

If the original document is dirty, replace.

Contact glass

Check whether the contact glass
is dirty.

If the contact glass is dirty, clean the contact
glass, and the bottom part of the shading plate.

FFC cable CCD

Check the FFC cable between
the CCD sensor and ISC PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

FFC cable LED

Check the FFC cable between
the LED PWB and ISC PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

SATA cable ISC

Check the SATA cable between
the ISC PWB and main PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

LED PWB

Check that the LED is lit.

If the LED is not lit, replace the LED PWB and

perform U411.

ISC PWB

The ISC PWB is defective.

Replace the ISC PWB and perform U411.

(see page 1-3-173)

Main PWB

The main PWB is defective.

Replace the main PWB.(see page 1-5-72)

Defective part

Check description

Corrective Action

Original document

Check whether the original

document is dirty.

If the original document is dirty, replace.

DP_CIS glass

Check whether the CIS glass of
the DP is contaminated.

If the CIS glass of the DP is contaminated,
clean. Or, if it has scuffs, replace.

DP_CIS unit

Check the location the CIS unit
is mounted.

Re-mount the CIS unit if it is hanged off.

DP_SHD PWB

Check the CIS and the SHD
PWB is properly connected.

Reinsert the connector if the PWB was loosely
inserted.If not cured, replace the PWB.

DP_SATA cable

Check the FFC cable between
the SHD PWB and ISC PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if its connection is
loose. Or, if conduction is lot, replace the wire.

DP_CIS

CIS is defective.

Replace the CIS and perform U091 and U411.
(see page 1-3-71,1-3-173)

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands

Kyocera TASKalfa 3051ci, Service Manual

Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands