Kyocera TASKalfa 3051ci Service Manual Download

Page: 230 / 317

2L6/2N6/2N5/2N4

1-4-229

(8) One side of the print image is darker or brighter than the other.

1. Table scanning

Print example

Defective part

Check description

Corrective Action

Original document

Check whether the original

document is dirty.

If the original document is dirty, replace.

Original document

Check if the original document

has creases or foldings or wrin-
kles.

If the original document has foldings or
creases, remove them.

Position of the mat
of the platen

Check whether the position of
the mat of the DP or the platen is
wrong.

If the position of the mat of the DP or the platen
is shifted, re-mount.

Contact glass

Check whether the contact glass
is dirty.

If the contact glass is dirty, clean the contact
glass, and the bottom part of the shading plate.

Contact glass assy Check the location the contact

glass is mounted.

Re-mount the contact glass if it is hanged off.

Lamp unit

Check the position at which the
light guide panel is mounted.

If the light guide panel has been fallen off of the
mounting position, fix it properly.

Mirror

Check whether the mirrors are
dirty.

If the mirrors are dirty, clean the three mirrors.

ISU

Check the location the ISU unit
is mounted.

Insert a spacer between the scanner unit and
the ISU to change the height.
(see page 1-5-36)

LED PWB

Check that the LED is lit.

If the LED is not lit, replace the LED PWB and

perform U411.(see page 1-3-173)

LED Assy

Check the mounting position of
the refelector board or if it is dis-
torted.

If the LED assy is hanged off of the mounting
position of the reflector or it is deformed,
replace the LED assy.

Lamp unit

Check that the contact part of
the lamp unit and the rail is dis-
torted.

If the contact part of the lamp unit and the rail is
distorted, replace the lamp unit.

Mirror unit

Check the location the mirror is
mounted.

Re-mount the mirror if it is hanged off. Or, if the
mirror is damaged, replace.

Mirror unit

Check that the contact part of
the mirror unit and the rail is dis-
torted.

If the contact part of the mirror unit and the rail
is distorted, replace the mirror unit.

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands

Kyocera TASKalfa 3051ci, Service Manual

Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands