background image

2L6/2N6/2N5/2N4-7

1-4-312

 (2-7) U017XX error code table: V.34 transmission

U01700/E01700:A communication error that occurs at the transmitting unit in the period after transmission of 

INFO0 before entering phase 3 (primary channel equivalent device training). For example, 
INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.

U01720/E01720:A communication error that occurs at the transmitting unit in the period after initiating the 

control channel before entering the T.30 process. For example, PPh/ALT/MPh/E was not 
detected.

U01721/E01721:In the absence of a common communication speed between units (including when an impos-

sible combination of communication speed and symbol speed occurs) after MPh exchange; 
1) a DCN signal was received from the destination unit, and the line was cut; or 2) a DIS 
(NSF, CSI) signal was received from the destination unit and, in response to the signal, the 
unit transmitted a DCN signal, and the line was cut.

 (2-8) U018XX error code table: V.34 reception

U01800/E01800:A communication error that occurs at the receiver unit in the period after transmission of 

INFO0 before entering phase 3 (primary channel equivalent device training). For example, 
INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.

U01810/E01810:A communication error that occurs at the receiver unit in phase 3 (primary channel equiva-

lent device training). For example, S/Sbar/PP/TRN was not detected.

U01820/E01820:A communication error that occurs at the receiver unit in the period after initiating the control 

channel before entering the T.30 process. For example, PPh/ALT/MPh/E was not detected.

U01821/E01821:In the absence of a common communication speed between units (including when an impos-

sible combination of communication speed and symbol speed occurs) after MPh exchange, a 
DCN signal was transmitted to the destination unit and the line was cut.

Error code

Description

U01700/E01700 A communication error occurred in phase 2 (line probing).

U01720/E01720 A communication error occurred in phase 4 (modem parameter exchange).

U01721/E01721 Operation was interrupted due to the absence of a common communication speed 

between units.

Error code

Description

U01800/E01800 A communication error occurred in phase 2 (line probing).

U01810/E01810 A communication error occurred in phase 3 (primary channel equivalent device training).

U01820/E01820 A communication error occurred in phase 4 (modem parameter exchange).

U01821/E01821 Operation was interrupted due to the absence of a common communication speed 

between units.

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Reviews: