Kyocera TASKalfa 3051ci Service Manual Download

Page: 316 / 317

2L6/2N6/2N5/2N4

1-4-315

shown on the MFP
application.

Connection error of
the harness
between the Main
board and the
bridge board(dam-
aged or loose con-
nected).

Wiring failure or loose con-
nection.

Reinsert the connector. Also
check for continuity within the
connector cable. If none, replace
the cable.

Defective bridge
board.

Bridge board mounting
error.

Replace the bridge board

and

check for correct operation.

Defective main
board.

Main board mounting error. Replace the main board

and

check for correct operation.

Defective Printing
system.

Board mounting failure in
the Printing system.

Replace the Printig system
board

and check for correct opera-

tion.

10.Fiery is not
detectable with Com-
mand Work Station.

Connection error of
the DVI
cable?(damaged or
loose connected).

Defective DVI cable or poor
contact.

Reinsert the connector. Also
check for continuity within the
connector cable. If none, replace
the cable.

Connection error of
the network cable
(damaged or loose
connected).

Local network cable failure
or loose connection.Failure
or wrong version.

Reinsert the network cable. Also
check for continuity within the
connector cable. If none, replace
the cable.

Connection error of
the network.

Network settings are incor-
rect with the MFP.

See item 9 above.

Network settings are incor-
rect with the PC.

See item 9 above.

FW version mis-
match.

The version does not match
with the MFP firmware and
the Printing system firm-
ware.

See item 7 above.

Connection error of
the harness
between the Main
board and the
Bridge board (dam-
aged or loose con-
nected).

Defective cable or poor
contact.

Reinsert the connector. Also
check for continuity within the
connector cable. If none, replace
the cable.

Defective bridge
board.

Bridge board mounting
error.

Replace the bridge board.

Defective main
board.

Main board mounting error. Replace the main board.

Defective Printing
system.

Board mounting failure in
the Printing system.

Replace the Printing system.

Problem/

Error code

Condition of

detection

Causes

Check procedures/ Corrective

measures

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands

Kyocera TASKalfa 3051ci, Service Manual

Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands