Kyocera TASKalfa 3051ci Service Manual Download | Manualshive

Page: 317 / 317

background image

2L6/2N6/2N5/2N4

1-4-316

(2) Remarks on Relay PWB replacement

To remove the FFC from the locked connector, unlock the connector by pressing the lock lever at the triangu-
lar mark.
To insert an FFC cable, hold it at both ends and insert it all the way in.

Figure 1-4-8

11.Printing is not
possible with Com-
mand Work Station.

Defective bridge
board.

Bridge board mounting
error.

Replace the bridge board.

Defective main
board.

Main board mounting error. Replace the main board.

Defective Printing
system.

Board mounting failure in
the Printing system.

Replace the Printing system.

12.An abnormal
printing occurs when
printing from Com-
mand Work Station.

Connection error of
the harness
between the Main
board and the
Bridge board (dam-
aged or loose con-
nected).

Defective cable or poor
contact.

Reinsert the connector. Also
check for continuity within the
connector cable. If none, replace
the cable.

Defective bridge
board.

Bridge board mounting
error.

Replace the bridge board

and

check for correct operation.

The image data is
not entered.

Engine board mounting
error.

Replace the engine board

and

check for correct operation.

Defective main
board.

Main board mounting error.

Replace the main board

and

check for correct operation.

Defective Printing
system.

Board mounting failure in
the Printing system.

Replace the Printing system

and

check for correct operation.

Problem/

Error code

Condition of

detection

Causes

Check procedures/ Corrective

measures

«
...
315
316
317

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 3051ci

Brand: Qls Pages: 53

Brand: Xerox Pages: 36

Brand: SA Pages: 5

Brand: WaxJet Pages: 131

Brand: Canon Pages: 149

Brand: Canon Pages: 60

Brand: Lanier Pages: 4

Brand: Oki Pages: 40

Brand: olympia electronics Pages: 4

Brand: Partner Pages: 9

WorkCentre 7525

Brand: Xerox Pages: 70

WorkCentre 7525

Brand: Xerox Pages: 8

WorkCentre 7328

Brand: Xerox Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 4

WorkCentre 7232

Brand: Xerox Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 236

WorkCentre 7232

Brand: Xerox Pages: 128

WorkCentre 7232

Brand: Xerox Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands