Kyocera TASKalfa 3051ci Service Manual Download | Manualshive

Page: 35 / 317

background image

2L6/2N6/2N5/2N4

1-4-34

No-paper-feed jam or
the leading edge of
paper is curled back at
the position of the
roller

(J0501,J0502,

J0503,J0504, J0505,

J0506, J0507J0509,

J0523, J0524, J0525,
J0526, J0527, J0545)

7. Check the separation

roller is not disturbed as
a driving component is
in contact with the
frame during the
separation roller is in
motion.

If it gets in contact, replace the primary feed unit.

8. Depress the release

lever to release the
pressure of the primary
feed rollers to check
that the retard holder
falls.(The pressure by
the retard roller to the
feed roller is
decreased.)

Modify mounting the retard holder fixing plate.

Multiple-feed Jam
(J0511, J0512, J0513,
J0514, J0516, J0517,
J0519)

1. Check if the cutting

edge of the paper
bundle is crumpled or
the cassette is loaded
with multiple times of
replenishing paper.

If the cutting edge of the paper bundle is crumpled or
the cassette is loaded with multiple times of
replenishing paper, load new paper.

2. Checking paper size.

Check that the size of
the loaded paper and
the paper size chosen
on the operator panel
are met.

If the paper size does not agree.

1. If the cassette cursors are open against the

paper, set it properly.

2. Insert the cassette until the paper size detector

switch is turned on.
If the size is not detectable while automatic sizing
is enabled, replace the size detection switch.

If the paper size agrees

1. If paper other than complying the requirements

such as coated paper, inkjet paper, etc., is used,
replace the paper.

2. RE-assemble the pulley retard in the primary

feed unit if it is mounted to the oppisite direction.

3. Check if the spring retard has not been fallen off

of the mounting position. If the spring retard is
not dropped off of the mount position, decrease
the spring pressure that is applied to the
separation rollers.

4. Replace the primary feed unit.

3. Check if paper dusts

and abrasion are
observed on the paper
fanning roller and retard
roller.

If the paper fanning roller is dirty, clean.
If abrasion is observed, replace.

Jam types

Check description

Corrective measures

«
...
33
34
35
36
37
...
»

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 3051ci

Brand: Ier Pages: 8

Brand: Samsung Pages: 347

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 180

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 18

SCX-4521FG - B/W Laser - All-in-One

Brand: Samsung Pages: 215

SCX 6320F - B/W Laser - All-in-One

Brand: Samsung Pages: 332

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 248

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 253

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 179

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 84

ML 1740 - B/W Laser Printer

Brand: Samsung Pages: 152

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 142

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 2

Brand: Samsung Pages: 384

Lazett Combo SCX-4216F

Brand: Samsung Pages: 135

Brand: Samsung Pages: 414

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands