Kyocera TASKalfa 3051ci Service Manual Download | Manualshive

Page: 69 / 317

background image

2L6/2N6/2N5/2N4

1-4-68

0840

Faults of RTC

displayed)
[Check at power up]
The RTC setting has reverted
to a previous state. The
machine has not been pow-
ered for 5 years (compared to
the settings stored periodically
in the EEPROM).
The RTC setting is older than
00:01 on January 1, 2000.
[Checked periodically (in 5-
minute interval) after powered
up]
The RTC setting has reverted
to a state older than the last
time it was checked.
10 minutes have been passed
since the previous check.

After C840 is detected, the
machine enters in disconnec-
tion mode after the main
power switch has been
switched on and off and indi-

Battery ( main
PWB)

1. Make sure that the back-up batteries on

the main PWB are not short-circuited.

2. Reset Maintenance T by executing

U906 (see page 1-3-224).

3. If the same C call is displayed when

power is switched on and off, replace the
back up battery.

4. If communication error (due to a noise,

etc.) is present with the RTC on the main
circuit PWB, check the PWB is properly
grounded.

Main PWB

Replace the main PWB (see page 1-5-72).

0870

PCFAX control PWB to main
PWB high capacity data
transfer error

High-capacity data transfer
between the FAX control PWB
and the main PWB of the
machine was not normally
performed even if the data
transfer was retried the speci-
fied times.

FAX control PWB

1. Turn the main power swtch off and after

5 seconds, re-mount the FAX controller
PWB, then turn power on.

2. Replace the FAX control PWB.

HDD

Execute U024 to initialize the HDD (see
page 1-3-32).

Main PWB

Replace the main PWB (see page 1-5-72).

0920

Fax file system error

The backup data is not
retained for file system abnor-
mality of flash memory of the
FAX control PWB.

FAX control PWB

1. Execute initializing by U600 (Refer to

the FAX service manual).

2. Replace the FAX control PWB.

0980

24 V power down detect

If a 24V power disconnection
signal is observed and a 12V
power disconnection signal is
observed simultaneously for
one second.

Power source
PWB

1. Check the +24V output is given at YC12-

1 to 3 of the power circuit PWB.

2. Replace the power source PWB (see

page 1-5-85)

Code

Contents

Related parts

Check procedures/

corrective measures

«
...
67
68
69
70
71
...
»

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 3051ci

CLP-680ND: CLP-775ND

Brand: Samsung Pages: 2

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: Partner Pages: 9

WorkCentre Pro 421

Brand: Xerox Pages: 4

WorkCentre Pro 412

Brand: Xerox Pages: 212

WORKCENTRE PE 220

Brand: Xerox Pages: 8

WORKCENTRE PE 220

Brand: Xerox Pages: 2

WORKCENTRE PE 220

Brand: Xerox Pages: 200

WorkCentre m940

Brand: Xerox Pages: 86

Brand: Xerox Pages: 24

WorkCentre PE16

Brand: Xerox Pages: 201

WorkCentre M24 Color

Brand: Xerox Pages: 441

WORKCENTRE C2424

Brand: Xerox Pages: 2

WorkCentre M118

Brand: Xerox Pages: 5

WORKCENTRE C2424

Brand: Xerox Pages: 16

WORKCENTRE C2424

Brand: Xerox Pages: 20

WORKCENTRE C2424

Brand: Xerox Pages: 25

2006NPC - DocuColor Color Laser

Brand: Xerox Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands