![background image](http://html1.mh-extra.com/html/kyocera/taskalfa-620/taskalfa-620_service-manual_2015981162.webp)
2KN/2KP
1-4-18
(21)
A paper jam in the
paper conveying sec-
tion is indicated dur-
ing copying (jam in
registration/transfer
section).
Jam code 34
Defective feed switch 1.
Run maintenance item U031 and turn feed switch 1 on and off
manually. Replace feed switch 1 if indication of the corresponding
sensor on the touch panel is not displayed in reverse.
Defective registration
switch.
Run maintenance item U031 and turn the registration switch on
and off manually. Replace the registration switch if indication of
the corresponding sensor on the touch panel is not displayed in
reverse.
The registration roller is
dirty with paper powder.
Check and, if it is dirty, clean it.
The registration roller is
deformed or worn.
Check and, if it is deformed or worn, fix or replace it.
(22)
A paper jam in the
paper conveying sec-
tion is indicated dur-
ing copying (jam in
registration/transfer
section).
Jam code 35
Defective feed switch 1.
Run maintenance item U031 and turn feed switch 1 on and off
manually. Replace feed switch 1 if indication of the corresponding
sensor on the touch panel is not displayed in reverse.
Defective registration
switch.
Run maintenance item U031 and turn the registration switch on
and off manually. Replace the registration switch if indication of
the corresponding sensor on the touch panel is not displayed in
reverse.
The registration roller is
dirty with paper powder.
Check and, if it is dirty, clean it.
The registration roller is
deformed or worn.
Check and, if it is deformed or worn, fix or replace it.
(23)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
1).
Jam code 40
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(24)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
2).
Jam code 41
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(25)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
3).
Jam code 42
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(26)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
4).
Jam code 43
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
Problem
Causes/check procedures
Corrective measures
Summary of Contents for TASKalfa 620
