![background image](http://html1.mh-extra.com/html/kyocera/taskalfa-620/taskalfa-620_service-manual_2015981163.webp)
2KN/2KP
1-4-19
(27)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
5).
Jam code 44
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(28)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
6).
Jam code 45
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(29)
A paper jam in the
fuser section is indi-
cated during copying
(jam in fuser section
7).
Jam code 46
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(30)
A paper jam in the
eject section is indi-
cated during copying
(jam in eject section).
Jam code 50
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
(31)
A paper jam in the
eject section is indi-
cated during copying
(jam in duplex feed-
shift section).
Jam code 60
Defective exit switch.
Run maintenance item U031 and turn the exit switch on and off
manually. Replace the exit switch if indication of the correspond-
ing sensor on the touch panel is not displayed in reverse.
Broken feedshift switch
actuator.
Check visually and replace the feedshift switch if its actuator is
broken.
Defective feedshift switch.
Run maintenance item U031 and turn the feedshift switch on and
off manually. Replace the feedshift switch if indication of the corre-
sponding sensor on the touch panel is not displayed in reverse.
Defective feedshift sole-
noid.
Run maintenance item U033 and select feedshift solenoid on the
touch panel to be turned on and off. Check the status and remedy
if necessary.
Electrical problem with
feedshift solenoid.
Check (see page 1-4-67).
The feedshift roller is dirty
with paper powder.
Check and, if it is dirty, clean it.
The feedshift roller is
deformed or worn.
Check and, if it is deformed or worn, fix or replace it.
Problem
Causes/check procedures
Corrective measures
Summary of Contents for TASKalfa 620
