2KN/2KP-2
1-3-4
Fuser and
cleaning
U161
Setting the fuser control temperature
Control temperature during copying
Primary stabilization fuser temperature
Secondary stabilization fuser temperature
Aging time after secondary stabilization
Control temperature adjustment in duplex copying
Time from power on to stabilization of fusing
Control temperature adjustment in duplex copying
using A4/Letter/B5 size paper
Control temperature adjustment when the fuser heater
temperature goes low
200
*1, *2
175 (120 V)/
140 (220-240 V)
*1, *2
185
*1, *2
60
*1, *2
-10
*1
26
*1, *2
-10
*1, *2
0
*1
195
*1, *2
175 (120 V)/
140 (220-240 V)
*1, *2
185
*1, *2
60
*1, *2
-10
*1
26
*1, *2
-10
*1, *2
0
*1
U162
Stabilizing fuser forcibly
-
U163
Resetting the fuser problem data
-
U167
Checking/clearing the fuser count
-
U169
Setting the fuser control mode
0
*1, *2
U180
Checking the cleaning count
-
U194
Setting the fuser web drive
66/3
*1
U196
Turning the fuser heater on
-
U198
Setting the fuser phase control
OFF (120 V)/ON (220-240 V)
*1, *2
U199
Displaying fuser heater temperature
-
Operation
panel/
Optional units
U200
Turning all LEDs on
-
U201
Initializing the touch panel
-
U202
Setting the KMAS host monitoring system
-
U203
Operating the DP separately
-
U204
Setting the presence or absence of a key card or key
counter
OFF
*1
U206
Setting the presence or absence of the coin vender
OFF
*1, *2
U207
Checking the keys on the operation panel
-
U208
Setting the paper size for the feeders
11 x 8.5 (inch)/A4 (metric)
*1, *2
U212
Setting the feeder lift operation
SIDE FEED
*1, *2
U233
Checking the operation of the side feeder switches
-
U234
Setting punch destination
NOTHING
*1
U235
Setting output tray initialize mode
HP ON
*1, *2
U237
Adjusting finisher stack quantity
0
*1, *2
U240
Checking the operation of the finisher
-
U241
Checking the operation of the switches of the finisher
-
U243
Checking the operation of the DP motors
-
U244
Checking the operation of the DP switches
-
U245
Checking messages
-
U247
Setting the paper feed device
-
U248
Changing the paper ejection device settings
Adjustment of registration stop timing in punch mode
Adjustment of the paper stop timing in punch mode
Punch-hole scrap count
Setting the booklet stapling position
Setting the center folding position
Punch limit
0
*1
0
*1
0
*1, *2
0/0/0
*1
0/0/0
*1
100000
*1, *2
Section
Item
No.
Content of maintenance item
Initial setting*
82 cpm
62 cpm
*Initial setting for executing U020, *1: The item initialized for executing U020, *2: The item initialized for executing U021
Summary of Contents for TASKalfa 620
