![background image](http://html1.mh-extra.com/html/kyocera/taskalfa-620/taskalfa-620_service-manual_2015981088.webp)
2KN/2KP
1-3-50
U161
Setting the fuser control temperature
Description
Changes the fuser control temperature.
Purpose
Normally no change is necessary. However, can be used to prevent curling or creasing of paper, or solve a
fuser problem on thick paper.
Method
1. Press the start key. The screen for selecting an item is displayed.
2. Select the item to be set and press the start key. The screen for setting is displayed.
Setting: PAGE1
1. Select the item to be set. The selecting item is displayed in reverse.
2. Change the setting using the cursor up/down keys.
The respective temperatures are to be set such that 2ND TEMP >= 1ST TEMP.
3. Press the start key. The value is set.
Setting: PAGE2
1. Select the item to be set. The selecting item is displayed in reverse.
2. Change the setting using the cursor up/down keys.
3. Press the start key. The value is set.
Supplement
While this maintenance item is being executed, the copy of whole surface black can be outputted in the inter-
rupt copying mode.
Completion
Press the stop/clear key at the screen for adjustment.
The screen for selecting a maintenance item No. is displayed.
Maintenance
item No.
Description
Display
Description
PAGE1
Control temperature during copying, primary stabilization fuser temperature, sec-
ondary stabilization fuser temperature, aging time after secondary stabilization,
control temperature adjustment in duplex copying and time from power on to stabi-
lization of fusing.
PAGE2
Control temperature adjustment in duplex copying using A4/Letter/B5 size paper
and control temperature adjustment when the fuser heater temperature goes low.
Display
Setting
Setting range Initial setting
CONT TEMP
Control temperature during copying
100 to 230
(
°
C)
200 (82 cpm)
195 (62 cpm)
1ST TEMP
Primary stabilization fuser temperature
100 to 200
(
°
C)
175 (120 V)
140 (220-240 V)
2ND TEMP
Secondary stabilization fuser temperature 100 to 230
(
°
C)
185
TIME
Aging time after secondary stabilization
0 to 255 (s)
60
DUPLEX
Control temperature adjustment in duplex
copying
-30 to 0 (
°
C)
-10
WARM UP TIME
Time from power on to stabilization of
fusing
0 to 255 (s)
26
Display
Setting
Setting range Initial setting
DUPLEX2
Control temperature adjustment in duplex
copying using A4/Letter/B5 size paper
(when optional document finisher is not
installed)
-30 to 0 (
°
C)
-10
SMALL
-
-
-
SPEED DOWN
Control temperature adjustmen when the
fuser heater temperature goes low
-10 to 10 (
°
C)
0
Summary of Contents for TASKalfa 620
