background image

― 14 ―

6.000A
10.00A
600.0μA
6000μA
60.00mA
600.0mA
6.000A
10.00A
600.0Ω
6.000kΩ
60.00kΩ
600.0kΩ
6.000MΩ
60.00MΩ

ACA

Resistance

Ω

±1.5%rdg±5dgt (50 / 60Hz)

±1.8%rdg±5dgt (40〜400Hz)
±1.2%rdg±3dgt (50 / 60Hz)

±1.5%rdg±3dgt (40〜400Hz)

Overload protection: 600V DC or AC

rms   Impedance: 10MΩ

0.1V or less is outside the accuracy

Crest factor(CF): 3.0 or less

Overload protection: 0.8A/600V

Overload protection: 10A/600V

Overload protection: 0.8A/600V

Crest factor(CF): 3.0 or less

Overload protection: 10A/600V

Crest factor(CF): 3.0 or less

Overload protection: 600V DC or AC rms.

±1.5%rdg±5dgt (50 / 60Hz)

±1.8%rdg±5dgt (40〜400Hz)

±1.2%rdg±3dgt

±2.0%rdg±5dgt

±1.5%rdg±4dgt(50/60Hz)

±2.0%rdg±4dgt(40〜1kHz)

Display read approximately forward voltage of diode

Built-in buzzer sounds if resistance is less then 100Ω

Description

Ranges

It  can  not  display  bar  graph  on  diode

range

Overload protection: 600V DC or AC rms.

Note

Forward DC current approx.0.4mA 

Reversed DC voltage approx.2.8V
Open circuit voltage approx.0.5V

Test condition

Note

It  can  not  display  bar  graph  on

capacitance range

It  can  not  display  bar  graph  on

frequency range

Overload protection: 600V DC or AC rms

Accuracy

±3.0%rdg±10dgt

±2.5%rdg±5dgt

±5.0%rdg±10dgt

±0.1%rdg±5dgt

±2.0%rdg±2dgt  Frequency lower then

10kHz Sensitivity: sine wave 0.6V rms

±2.2%rdg±5dgt(50/60Hz)

±2.5%rdg±5dgt(40〜1kHz)

±1.0%rdg±2dgt

±2.0%rdg±3dgt

0〜600V

(4 Auto ranging)

0〜6000μA

(2 Auto ranging)

0〜600mA

(2 Auto ranging)

0〜6000μA

(2 Auto ranging)

0〜600mA

(2 Auto ranging)

0〜10A

(2 Auto ranging)

0〜60MΩ

(6 Auto ranging)

0〜10A

(2 Auto ranging)

6.000V

60.00V
600.0V

600V

600.0μA
6000μA
60.00mA
600.0mA

ACV

DCA

Function

Capacitance

Frequency

Ranges

40.00nF
400.0nF
4.000μF
40.00μF
400.0μF
4000μF
10Hz
100Hz
1000Hz
10kHz
100kHz
1000kHz
10MHz

DUTY

Measuring range

0.01nF〜4000μF

(6 Auto ranging)

1Hz〜10MHz

(7 Auto ranging)

Input which can be

measured : Voltage :

〜1MHz = more than 1.5V

1〜10MHz = more than 2V

0.1〜99.9%

(Pulse width/Pulse period)

Summary of Contents for KEW 1012













Reviews: