7
No.1
4
Gear Differential
MAINTENANCE
Ball Differential Grease
EXPLODED VIEW
54
Thrust Washer
2
55 1/16
Thrust Ball
8
37
Thrust Plate
2
38 3/32
Ball Bearing
12
< >
< Ball Diff unit >
2
50 4 x 8mm
Ball Bearing
34
41
55
54
54
39
35
37
37
35
34
Part bags used.
Apply grease.
38
36
34
Assemble with the aid of the above exploded view and pay
attention to the following.
Remove oil deposits from before applying a small amount of ball
differential grease to the spots marked with .
Secure parts and in place with two flat head screwdrivers
and rotate the differential case until it becomes tight. Then, tighten
screw . When running the car, the differential must be tight,
otherwise it may be damaged.
After applying Grease, place
eight differential balls bet-
ween the two thrust washers
, grouping them around
the screw .
55
54
39
Place the differential balls into
and apply ball differential grease.
38
Tighten 34 with a screwdriver
and fully tighten 39 then rewind
1/8 turn.
(Adjust it later)
Once the adjustment is done,
install (see"exploded view").
41
34
39
35
Now, hold the differential case firmly and rotate part . If part
rotates into the opposite direction to part , no further adjustment
is necessary. If part does not rotate, screw is too tight.
In this case, gradually loosen screw until part rotates.
As soon as the ball differential's smooth action becomes rough,
parts , , and may have become "gritty". If this
happens, disassemble the unit and clean these parts, apply more
grease and reassemble. If the action is still not smooth, the parts
are worn and, therefore, must be replaced. We recommend that
these parts be replaced from time to time to ensure smooth running.
35
36
36
39
39
36
35
37 38 54
55
40
45
34
50
37
38
37
50
35
55
39
41
36
54
39
使用する袋詰。
グリスを塗る。
デフギヤ
分解図
スラストワッシャー
スラストボール
スラストプレート
ベアリング
ボールデフユニット
ベアリング
組立ては上の分解図を参考にしてください。
下記の点に注意してください。
ボールデフグリス
油分をとり(脱脂)、
の所にボールデフグリスを少し塗る。
と
をマイナスドライバーで固定し、本体を回してみる。
回らなくなるまで
をしめ込む。回ってしまう状態のまま走行
させると破損するので注意。
はグリスを塗った
に
8
個並べる。
55
39
54
を
に組込み、ボールデフ
グリスを塗る。
38
調整後、
を取付ける。
41
36
をマイナスドライバーで
固定し、 をいっぱいにしめ
込み、それから1/8回転ゆるめる。
(後で調整する)
34
39
34
35
次に本体を手で固定し、
を回したとき、
が反対方向に回転す
れば良い。回らないときはしめ込み過ぎなので、
をゆるめる。
作動させたときになめらかに動かなくなったら、
, , ,
が汚れています。分解して掃除してください。それでも直らない
ときは、これらのパーツが消耗しているので交換してください。
また、これらのパーツは定期的に交換するとよいでしょう。
39
35
37 38 54 55
36
メンテナンス