▲
▲
プロポの準備
●プロポを下の順番にしたがってセットします。
■スティックタイプ
■ハンドルタイプ
送信機
送信機
●始める時
●終わる時
送信機に単
3
乾電池をセットする。
送信機のアンテナをのばす。
電池ボックスに単
3
乾電池を
セットする。
電池ボックスのコネクター
をつなぐ。
受信機のアンテナをのばす。
トリムを中央にセットする。
送信機のスイッチを入れる。
受信機のスイッチを入れる。
ハンドル
/
トリガーを動かし
てサーボが動いているか確認。
受信機のスイッチを切る。
送信機のスイッチを切る。
送信機のアンテナを縮める。
▲受信機
▲スイッチ
サーボ
▲電池ボックス
▲
説明書の見かた
組立て前の注意
組立ての前に下記のことに注意してください。
●この説明書を良く読み、構造を理解する。
●キットの内容を確かめる。
※万一不良、不足がありましたら、お買い求めの販売店か、当社「ユーザー相談室」までご連絡ください。
●小さな部品の形やサイズを間違えないようにする。図を参考にして確認しながら組立てる。
●TPビス締をめるときは・・・
締めこみが固くても部品が固定されるまで締めてください。ただし、部品が変形するまで締めるとビスがきかなくなります。
この項目で組立てるおおよその場所。
小物部品の名前、原寸図、使用数。
キット内の部品は、ビス類を除いてキー
No.
が付けられています。
スペアパーツを購入する時はキー
No.
を参照してください。
説明書内では多くのマークが使用されています。
マークに注意して組立てを進めてください。マークの説明は、
各ページの下にあります。
説明例
フレーム
L
の刻印
TPビス
RADIO PREPARATION
Set up the radio as explained below.
Stick-type
Wheel-type
Transmitter
Transmitter
ON
OFF
1
2
12
6
11
7
9
1
2
12
6
11
7
9
ON
OFF
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
●START
●FINISH
Insert AA-size batteries into
the Transmitter.
Extend the Transmitter antenna.
Insert the AA-size batteries
into the battery box.
Plug in the battery box.
Unwind the Receiver antenna.
Center the Transmitter trims.
Switch "ON" the Transmitter.
Switch "ON" the Receiver.
Make sure the servos move ac-
cording to your transmitter inputs.
Switch "OFF" the Receiver.
Switch "OFF" the Transmitter.
Retract the Transmitter antenna.
Servo
Switch
Receiver
Battery Box
5
4
3
8
10
ON
OFF
1
2
Correct
Wrong
Before assembling, please read the following carefully:
Check the contents of this kit. Should parts be missing, immediately contact the retail shop or your nearest Kyosho distributor.
When tightening a self-tapping (TP) screw: continue tightening until fastened correctly,
even if screw is hard to turn.
However, do not overtighten it as the plastic thread inside the part may strip!
First, read through this instruction manual and understand the modelÕs con-struction.
Do not use the wrong size or shaped small parts. Check the illustrations & use the correct
part for each step of assembly.
〔 Example 〕
How to read the instruction manual:
BEFORE YOU BEGIN
A:
B:
C:
D:
A: Indicates the assembly step number and the section that will
be assembled.
B: Key Number, Part Name, True-to-scale Diagram, Quantity Used.
C: All parts except screws are identified by key numbers.
For purchasing spare parts, find the key number of the part
needed in the spare parts list and refer to the left column for the
corresponding order number.
D: This instruction manual uses several symbols.
Please note them during the entire assembly at the bottom of
each page.
3
A
B
C
D
Frame
6
"Left" side mark.
2
3 x 10mm
TP Screw
3 x 10mm
12
12