L-Acoustics KIVA SB18m Rigging Manual Download

Page: 10 / 12

SB18

SUBWOOFER

rigging manual

VERSION 1.0

SB18

_RM_EN_1-0

w w w . l - a c o u s t i c s . c o m

Installing a shackle or CLAMP250

Refer to

SOUNDVISION

modeling to identify the hole number that corresponds to the desired tilt angle.

Hole numbering

FRONT

REAR

WIFOBUMP

About site angle

As many variables can affect the actual site angle, it is recommended to use an inclinometer.

Secure a shackle or CLAMP250 to the identified hole.

Attach the shackle or the CLAMP250 bar to the identified hole, by driving the pierced bolt and securing the nut.

Lock the pierced bolt with the safety pin.

With CLAMP250, install safety slings between the WIFOBUMP and the truss.

PROCEDURE B

: Locking a shackle or CLAMP250

A shackle being attached on the WIFOBUMP

A CLAMP250 being attached on the WIFOBUMP

Safety pin mechanism on shackles

Unlock

Lock

Summary of Contents for KIVA SB18m













Search results

Summary of Contents for KIVA SB18m

Reviews:

Related manuals for KIVA SB18m

Brands by name

Popular brands

L-Acoustics KIVA SB18m, Rigging Manual

Search results

Summary of Contents for KIVA SB18m

Reviews:

Related manuals for KIVA SB18m

Brands by name

Popular brands