background image

La Crosse Technology, Ltd.  

Page 7 

 

 

12H/24H 

 

Hour 

 

 

 

 

 

 

Minutes   

 

 

 

 

Year 

 

 

 

 

Month 

 

Date 

 

Temperature Fahrenheit/Celsius 

 

To begin: 
1.

 

Hold the SET button 3 seconds to select atomic time ON/OFF. ATOMIC ON will show. 

ON flashes. 

2.

 

Press +/HI or -/LO button if you do not want Atomic Time signal (OFF). 

Note: if ATOMIC is set to OFF; Skip DST, and Time Zone settings and go directly to 

12/24 hour Format. 

3.

 

Press SET to confirm and move to the Daylight Saving Indicator. DST ON will show. ON 

flashes. 

4.

 

Press +/HI or -/LO button to turn DST OFF if you do not observe Daylight Saving Time 

changes. 

5.

 

Press SET to confirm and move to the Time Zone. EASTERN will flash.  

6.

 

Press +/HI or -/LO button to select your time zone. 

7.

 

Press SET to confirm and move to 12/24 hour time format. FORMAT will show. 12Hr 

flashes. 

8.

 

Press +/HI or -/LO button to turn select 24 hour time format. 

9.

 

Press SET to confirm and move to the hour. SET HOUR will show. The hour flashes. 

10.

 

Press +/HI or -/LO button to choose the hour. 

11.

 

Press SET to confirm and move to the minutes. The MINUTES will show. Minutes flash. 

12.

 

Press +/HI or -/LO button to choose the minutes. 

13.

 

Press SET to confirm and move to the year. The SET YEAR will show. 2017 will flash. 

14.

 

Press +/HI or -/LO button to change the year. 

15.

 

Press SET to confirm and move to the month. The MONTH will show. Month will flash. 

16.

 

Press +/HI or -/LO button to change the month. 

17.

 

Press SET to confirm and move to the date. SET DATE will show. Date will flash. 

18.

 

Press +/HI or -/LO button to change the date. 

19.

 

Press SET to confirm and move to the temperature unit. TEMP °F will show. ̊F will flash. 

20.

 

Press +/HI or -/LO button if you prefer °C (Celsius). 

21.

 

Press SET to confirm and exit. 

  

WWVB ATOMIC TIME SIGNAL 

 

 

Once batteries are installed, your station will automatically search for the atomic time 

signal for 5 minutes. Your station will search again at UTC 7:00, 8:00, 9:00, 10:00, and 
11:00. 

 

If there is no WWVB reception, your station will search for the atomic time signal every 
2 hours until the WWVB time is received.  

 

The atomic time signal icon will flash while searching.  The tower icon will be solid 

when it has connected. 

 

After reception, this station will only search for the atomic signal after midnight. 

Summary of Contents for 308-1412-3TX










Reviews: