background image

La Crosse Technology, Ltd.  

Page 9 

 

1.

 

Check for a Tower Icon showing on the display near the time. The tower icon indicates 

successful reception of the WWVB signal in the past 24-hours.  

2.

 

Check that the Weather Station is in the correct Time Zone. This station offers seven 

time zones listed in letter format (default is EST):  

 

Atlantic  

 

Eastern  

 

Central  

 

Mountain  

 

Pacific  

 

Alaskan  

 

Hawaiian  

3.

 

Check that ATOMIC is ON. This must be ON to receive a WWVB atomic time signal. 

4.

 

Check that the DST indicator is ON. If the indicator is OFF the weather station will not 

change into or out of Daylight Saving Time. 

5.

 

Batteries dated earlier than 6 years from now may still work, but may be unstable in 

performance.  

  Note: Without proper batteries, the antenna will have a harder time picking up the 

signal. 

  

 

For information about WWVB visit: 

http://bit.ly/AtomicTime

   

 

BACKLIGHT 

 

Power cord: The backlight is on continuously when operating the station with the power 

cord. 

When operating with the power cable, press and release the LIGHT button to adjust the 

backlight. 

 

Note: When the power cord is NOT in use, the Hi/Low/Off light feature is not available. 

 

Try this exercise in a dim room.  The weather station has a bright, dim and OFF setting for 

the backlight. Wait 15 seconds after pressing the LIGHT button to see if backlight stays on. 

This will assure it is not in OFF mode. 

  

1.

 

Be sure the power cord is plugged in correctly to the weather station and the outlet. 

2.

 

Remove the batteries. 

3.

 

Press the LIGHT button. If the backlight comes on and the display is active your power 

cord works. 

4.

 

Wait 15 seconds to see if the back light stays on.  

5.

 

If the backlight goes out after 15 seconds, repeat #3. 

 

FORECAST ICONS INACCURATE 

 

The forecast icons are determined by the station's barometric pressure reading. Please 

allow 7-10 days for barometric calibration. Six forecast icons use changing atmospheric 

pressure to predict weather conditions for the next 12-hours with 70-75% accuracy. 

When Outdoor temperature is below 32˚F and the forecast is RAIN or T-STORM, the 

station will display SNOW.  

 

Forecast Icons: 

Summary of Contents for 308-1416v2












Reviews: