background image

 

12 

 

 

View MIN/MAX data: 

Press and release the MAX/MIN button to view the Maximum, Minimum, then Current 

Indoor and Outdoor Temperatures.

 

   

 

Multiple Transmitters: 

Press and release the CH button to select the desired outdoor channel to view the 

Minimum and Maximum Outdoor Temperatures. Press and release the MAX/MIN button to view the 
Maximum, Minimum then Current Temperatures for that channel.

   

 

 

Reset all MIN/MAX data: 

Hold the MAX/MIN button for 5 seconds and the Indoor and all Outdoor Minimum 

and Maximum Temperatures will be reset manually to Current temperatures.    

 

Low Battery Indicator    

 

  When this icon 

 appears in the indoor (IN) reading section, replace the batteries in the forecast station.  

  When this icon 

 appears in the outdoor (OUT) readings section, replace the batteries in the outdoor 

transmitter. 
 

Use Multiple Outdoor Transmitters  

 
The forecast station will accommodate up to three remote outdoor transmitters (TX14TH). The channel selection 
button allows you to easily see the temperature in various locations: outdoors, baby’s room, greenhouse, 
basement, etc. 
 

To connect multiple remote transmitters to the forecast station: 

 
1.  Remove the battery cover from all the transmitters (Leave battery covers off until all 

transmitters are received by the forecast station). 

2.  Set the first outdoor transmitter to Channel 1 and insert 2 AA batteries.  
3.  Set the second outdoor transmitter to Channel 2 and insert 2 AA batteries. 
4.  Set the third outdoor transmitter to Channel 3 and insert 2 AA batteries. 
5.  Press and hold CH button on the forecast station for 5 seconds. The forecast station will 

search for all outdoor transmitters. 

6.  Press the TX button on each outdoor transmitter to transmit RF signal. 
7.  When RF connection is established, the respective temperature & humidity for each of the 

selected channels will appear on the main unit.  

8.  Allow the transmitters and the forecast station to stay 5-10 feet apart for 15 minutes to 

establish a solid connection. 

9.  Install the battery covers on each sensor. 
10. 

After 15 minutes place the remote transmitters in appropriate locations (see “

position the outdoor 

transmitter

”). 

 
Press and release the CH button to view channel 1, 2 or 3 on the forecast station when multiple 
transmitters are used.

 

 

Note:

 You cannot change channels if only one transmitter is connected. 

 
Channel Scroll 

 

Press and release the CH button until you see  

  appear in the outdoor data area. The forecast station will 

automatically rotate through the channels for all connected transmitters.   
 
Press and release the CH button to lock the forecast station into one channel. Then view channels individually 
with a press of the CH button. 
 

Install Batteries in the Forecast Station 

 

Summary of Contents for 308-1451



















Reviews: