background image

3 | 

P a g e

 

 

CA82738-1:

 5 volt power cord (required) and 2-AA batteries for optional backup of your 

time and date. Power cord is required. 

 
CA82738-2:

 2-AAA batteries 

WILL THESE STATION WORK IN OTHER COUNTRIES? 

 

No. The color station will only work on 120 volt systems. 

SETUP: HOW DO I SETUP MY STATION? 

 

1.

 

Insert 2-AA batteries into your Outdoor Sensor. 

2.

 

Insert the 5 volt power cord into an outlet, then into your Color Display. Optional: Insert 

2-AA batteries for backup. 

3.

 

Insert 2-AAA batteries into your Mini Display.  

4.

 

Adjust time and date settings on each display. 

5.

 

Once the Outdoor Sensor is reading to each of your displays, place it outside in a 

shaded location. 

    .

MOUNTING: WHERE DO I POSITION MY SENSOR & STATION? 

 

 

Watch sensor mounting video: 

http://bit.ly/TH_SensorMounting

 

 

Place your thermo-hygro sensor at least 6 feet off the ground. 

 

For accurate temperature readings your sensor needs to be shaded from the sun and in a 
well ventilated area. Trapped moisture will cause inaccurate readings. 

 

Mount your sensor vertically to allow moisture to drain out the bottom. 

 

Preferred location is on a north facing wall under an eave or deck rail. 

 

Avoid placing near a metal roof that will cause it to read high on sunny days. 

 

Avoid other sources of heat such as soffit vents, and window or door frames. 

 

For accurate humidity readings, avoid placement near vegetation and lakes or other 

bodies of water when possible. 

 

Maximum transmission distance from your thermos-hygro sensor to your station, in open 
air is 330 feet (100 meters).  

 

 Insert the mounting screw through the front of the transmitter and into the wall. Tighten 

the screw to snug (do not over tighten). 

POSITION STATIONS 

 
Your stations are designed for placement on a desk or countertop. 

 

Position within reach of an outlet that is always active. Some outlets in living rooms and 
in bedrooms may only be active when the light switch is on. 

 

This color station must operate with the 5 volt power cord in order to receive sensor 
updates. Operation on battery power will only maintain time/date settings if you need to 
move your station. 

Summary of Contents for Wireless Weather Station












Reviews: