background image

 

15 

 

CARE AND MAINTENANCE:

 

 

Extreme temperatures, vibration and shock should be avoided as these may cause damage to the unit and give inaccurate forecasts and readings. 

 

Precautions shall be taken when handling the batteries. Injuries, burns, or property damage may be resulted if the batteries are in contact with conducting materials, 
heat, corrosive materials or explosives. The batteries shall be taken out from the unit before the product is to be stored for a long period of time. 

 

Immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type. 

 

When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or scouring agents as they may mark the LCD and casings. 

 

Do not submerge the unit in water. 

 

Special care shall be taken when handling a damaged LCD display. The liquid crystals can be harmful to user's health. 

 

Do not make any repair attempts to the unit. Return them to their original point of purchase for repair by a qualified engineer. Opening and tampering with the unit 
may invalidate their guarantee.  

 

Never touch the exposed electronic circuit of the device as there is a danger of electric shock should it become exposed. 

 

Do not expose the units to extreme and sudden temperature changes, this may lead to rapid changes in forecasts and readings and thereby reduce their accuracy. 

 

SPECIFICATIONS:

 

Temperature measuring range: 
Indoor  

:  32°F to +140°F with 0.2°F resolution  

 

  0ºC to +59.9ºC with 0.1ºC resolution 

 

(“OF.L” displayed if outside this range) 

Outdoor / dew point : 

-40°F to +140°F with 0.2°F resolution 

 

   

-40ºC to +59.9ºC with 0.1ºC resolution 

 

 

(“OF.L” displayed if outside this range) 

Relative humidity measuring range: 
Outdoor 

 

:  1% to 99% with 1% resolution 

 

(“- -” displayed if < 1%, "99" displayed if 

 99%) 

Wind speed/ gust  : 

0 to 111.8 mph (0 to 50 m/s)  

 

(displayed "OF.L" when > 111.8 mph; 50m/s) 

Wind chill/ dew point: 

-40°F to +140°F (-40ºC to +59.9ºC) 

 

(displayed "OF.L" if outside this) 

Relative pressure pre-set range  : 

27.17 to 31.90 inHg (919 to 1080 hPa) 

24h rainfall 

0" to 39.36" (0 to 999.9 mm) 

 

 

(displayed "OF.L" when > 999.9mm) 

Total rainfall

 

0" to 393.6" (0 to 9999 mm)  

 

 

(displayed "OF.L" when > 9999mm) 

Outdoor data reception  :  

every 4.5 seconds (from thermo-hygro  

 transmitter) 
 

every 6.25 seconds (from rain sensor) 

Air pressure checking interval: every 15 seconds 
Transmission range 

:  

up to

 330 feet (100 meters)

 in open space 

Power consumption: 
Weather Center 

:  

3 x AA, IEC LR6, 1.5V 

Thermo-hygro transmitter : 

2 x AA, IEC LR6, 1.5V 

Rain sensor 

2 x AAA, IEC LR3, 1.5V 

Battery life 

 

approximately 24 months (Alkaline batteries recommended) 

Dimensions (L x W x H): 
Weather Center 

 

:   

4.59” x 0.94” x 7.01” 

 

 

    (116.8 x 24 x 178.1mm)

 

Thermo-hygro transmitter :    2.25” x 2.44” x 6.18”  
 

 

    (57.3 x 62 x 157mm) 

Wind sensor 

:    9.84” x 5.74” x1087”  

 

 

    (250 x 145.9 x 276.2mm) 

Rain sensor 

:    5.67” x 2.15” x3.46”  

 

 

    (144 x 54.6 x 88mm)

  

 
 
 
 

LIABILITY DISCLAIMER 

 

The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in wild country and/or in unauthorized grounds strongly damages 
the environment. 

 

Please contact your local or/and regional authorities to retrieve the addresses of legal dumping grounds with selective collection. 

 

All electronic instruments must from now on be recycled. User shall take an active part in the reuse, recycling and recovery of the electrical and electronic waste. 

 

The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. 

 

As stated on the gift box and

 labeled o

n the product, reading the “User manual” is highly recommended for the benefit of the user. This 

product should not 

be thrown 

in general rubbish collection points. 

 

The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any consequences that occur should an inaccurate reading take place. 

 

This product is designed for use in the home only as indication of the temperature. 

 

This product is not to be used for medical purposes or for public information. 

 

The specifications of this product may change without prior notice. 

 

This product is not a toy. Keep out of the reach of children. 

 

No part of this manual may be reproduced without written authorization of the manufacturer. 

 

WARRANTY INFORMATION 

 

La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. 

 

This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this 

product.  To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.  Warranty service can 

only be performed by a La Crosse Technology, Ltd authorized service center.  The original dated bill of sale must be presented upon request as proof of purchase to La 

Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. 

 

La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be 

defective during the limited warranty period specified above.  All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to 

La Crosse Technology, Ltd.  Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.  La Crosse Technology, 

Ltd will pay all expenses for labor and materials for all repairs covered by this warranty.  If necessary repairs are not covered by this warranty, or if a product is examined 

which is not in need or repair, you will be charged for the repairs or examination.  The owner must pay any shipping charges incurred in getting your La Crosse 

Technology, Ltd product to a La Crosse Technology, Ltd authorized service center.  La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the 

product to a USA address only. 

 

Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, 

unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the 

carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner’s manual; 

(5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units 

used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference..  

This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or 

adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. 

 

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED 

WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.  THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC 

INFORMATION.  THIS PRODUCT IS NOT A TOY.  KEEP OUT OF CHILDREN’S REACH. 

 

This warranty gives you specific legal rights.  You may also have other rights specific to your State.  Some States do no allow the exclusion of consequential or incidental 

damages therefore the above exclusion of limitation may not apply to you. 

 

Summary of Contents for WS-1510-IT




















Reviews: