4. Wait 15 minutes to allow both the indoor and outdoor
temperatures are shown on the indoor temperature
station.
5. The indoor temperature station should now show: "-:- -
" in the TIME LCD, and temperatures in the INDOOR
and OUTDOOR LCD's.
II. TIME
A. SETTING THE TIME
1. Press and hold the "SET" button for 5 second, "12h"
will appear in the TIME LCD.
2. Press and release the "MIN/MAX" button to select either
12h time (am/pm) or 24h time
3. Press and release the "SET" button 2 times, the hour
will flash in the upper left corner.
4. Press and release the "MIN/MAX" button to set the hours
5. Press and release the "SET" button to move to the
GB
P.6
GB
P.7
GB
P.8
GB
SET
TIME
INDOOR
OUTDOOR
2
433 MHz
CH
MIN/MAX
RESET/+
SET
CH
MIN/MAX
RESET/+
P.9
+
SIZE AAA
+
SIZE AAA
Battery cover
Battery
compartment
DETAILED SETUP GUIDE
I. BATTERY INSTALLATION
A. REMOTE TEMPERATURE SENSOR
1. Remove the mounting bracket.
2. Remove battery cover
3. Observing the correct polarity,
install 2 AAA batteries-make
sure they do not spring free, or
start-up problems may occur.
Replace cover.
B. INDOOR TEMPERATURE STATION
Note
: After the batteries are installed, DO NOT press any
buttons. This may interfere with the signals, causing
temperatures to register incorrectly.
1. Remove the battery cover on the backside. To do this,
push up and pull out.
2. Observing the correct polarity, install 2 AAA batteries.
3. Replace battery cover.
minute setting
6. Press and release the "MIN/MAX" button to set the
minutes.
7. Press and release the "SET" button to activate the clock.
Note
:
When in 12h mode, there is only a "PM" display,
which appears under "TIME." If there is no display here it
is AM. Make sure you set the time accordingly.
III. UNITS OF TEMPERATURE MEASURE
A. SELECTING UNITS OF MEASUREMENT
1. Press and hold the "SET" button for 5 second until "12h"
or "24h" appears in the TIME LCD.
2. Press and release the "SET" button again, "˚F" will
appear in the TIME LCD.
3. Press and release the "MIN/MAX" button to shift
between ˚F and ˚C.
4. Press and release the "SET" button twice to activate
settings.
IV. FEATURES
A. MINIMUM AND MAXIMUM TEMPERATURES
1. Press and release the "MIN/MAX" button, "MIN"
appears in the temperature LCD's and the recorded
minimum temperatures are displayed.
2. Press and release the "MIN/MAX" button to toggle to
the maximum temperatures. The time of occurrence of
the value for outdoor temperature will also flash.
B. RESETTING THE MINIMUM AND MAXIMUM
TEMPERATURES
1. To reset both the minimum and maximum temperatures-
press and hold the "RESET/+" button for 4 seconds.
C. ADDING ADDITIONAL REMOTE TEMPERATURE
SENSORS (OPTIONAL)
1. The WS-7013U is able to receive signals from 3 different
remote temperature sensors. Following are some brief
instructions for the basic set-up of remote temperature
sensor units with the WS-7013U. These extra sensors
can be purchased through the same dealer as this unit,
or by contacting La Crosse Technology directly. A TX2U
and TX6U will monitor temperature only, a TX3U will
monitor temperature and display the temperature on its
LCD, and the TX3UP will monitor the temperature via a
probe for use in pools, spas, etc.
Note
: When setting up multiple units it is important to
remove the batteries from all existing units in operation,
then to insert batteries first into all the remote temperature
sensor units, and in numeric sequence. Second, install
batteries into the indoor temperature station. Transmission
problems will arise if this is not done correctly and if the
total time for set-up exceeds 6 minutes.
2. It is necessary to remove the batteries from all units
currently in operation.
3. Remove the battery covers to all remote temperature
sensor units.
4. Place all remote temperature sensor units in a numeric
sequential order.
5. In sequential order, install batteries (follow the same
REMOTE
TEMP. TRANSMITTER
433 MHz
+
SIZE AAA LR3
+
SIZE AAA LR3
Battery cover
Battery compartment
