background image

 

23

WARRANTY INFORMATION 

La Crosse Technology, Ltd provides a 1-year limited warranty on this product against 
manufacturing defects in materials and workmanship. 
 
This limited warranty begins on the original date of purchase, is valid only on products 
purchased and used in North America and only to the original purchaser of this 
product.  To receive warranty service, the purchaser must contact La Crosse 
Technology, Ltd for problem determination and service procedures.  Warranty service 
can only be performed by a La Crosse Technology, Ltd authorized service center.  
The original dated bill of sale must be presented upon request as proof of purchase to 
La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. 
 
La Crosse Technology, Ltd will repair or replace this product, at our option and at no 
charge as stipulated herein, with new or reconditioned parts or products if found to be 
defective during the limited warranty period specified above.  All replaced parts and 
products become the property of La Crosse Technology, Ltd and must be returned to 
La Crosse Technology, Ltd.  Replacement parts and products assume the remaining 
original warranty, or ninety (90) days, whichever is longer.  La Crosse Technology, Ltd 
will pay all expenses for labor and materials for all repairs covered by this warranty.  If 
necessary repairs are not covered by this warranty, or if a product is examined which 
is not in need or repair, you will be charged for the repairs or examination.  The owner 
must pay any shipping charges incurred in getting your La Crosse Technology, Ltd 
product to a La Crosse Technology, Ltd authorized service center.  La Crosse 
Technology, Ltd will pay ground return shipping charges to the owner of the product to 
a USA address only. 
 
Your La Crosse Technology, Ltd warranty covers all defects in material and 
workmanship with the following specified exceptions: (1) damage caused by accident, 
unreasonable use or neglect (including the lack of reasonable and necessary 
maintenance); (2) damage occurring during shipment (claims must be presented to 
the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; 
(4) damage resulting from failure to follow instructions contained in your owner’s 
manual; (5) damage resulting from the performance of repairs or alterations by 
someone other than an authorized La Crosse Technology, Ltd authorized service 
center; (6) units used for other than home use (7) applications and uses that this 
product was not intended or (8) the products inability to receive a signal due to any 
source of interference..  This warranty covers only actual defects within the product 
itself, and does not cover the cost of installation or removal from a fixed installation, 
normal set-up or adjustments, claims based on misrepresentation by the seller or 
performance variations resulting from installation-related circumstances. 
 
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR 
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES 
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.  
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR 

Summary of Contents for WS-7014U

























Reviews: