background image

 

11

2) ACTIVATING/DEACTIVATING THE ALARM 
 

(a)  The alarm will be automatically set to sound when exiting the alarm-

setting mode (indicated by the alarm “sound” icon to the right of the 
time).

 

(b)  Press and release the “

ALARM”

 button to activate and deactivate the 

alarm. The alarm “sound” icon to the right of the time will appear or 
disappear, and the alarm time will be displayed briefly before returning 
to the normal display mode.

 

 

3)  ACTIVATING THE SNOOZE FUNCTION 
 

While the alarm is sounding, press and release the 

“SNOOZE”

 button to 

activate the snooze function.   
The alarm “sound” icon and “SNOOZE” icon (to the right of the time) will 
flash. 
The duration of the snooze function is 10 minutes, then the alarm will 
resume.

 

 

4) SUSPENDING 

ALARM 

 

While the alarm is sounding or the SNOOZE is active, press and release the 

“ALARM” 

button to suspend the alarm until the next day.

 

C) INDOOR TEMPERATURE 

 

The Indoor temperature appears on the right side of the Date LCD.  The 
temperature is checked every 10 seconds, and updated whenever there is a 
change.

 

D) REMOTE TEMPERATURE 

 

The remote temperature will be shown on the right side of the lower LCD 
screen. The temperature clock receives the outdoor temperature (

°

F or 

°

C) from 

the remote temperature sensor, and the temperature appears in the OUTDOOR 
LCD.  The remote temperature sensor transmits a new temperature to the 
weather temperature clock 3 times every 10 minutes.

 

Summary of Contents for WS-8011MTWC



















Reviews: