background image

 

5

5.

 

Replace the humidity hood. 

 

B.

 

INDOOR WEATHER STATION 

1.

 

Remove the battery cover. To do this, insert a solid object in the 
space provided at the lower-central position of the battery cover, 
then push up and pull out on the battery cover. 

2.

 

Observe the correct polarity, and install 3 AA batteries. 

3.

 

Replace the battery cover. 

 

Note:

  Immediately after the batteries have been installed, the 

LCD (Liquid Crystal Display) will flash. Within 15 seconds the 
indoor temperature, indoor relative humidity, and the weather icons (sun and clouds) will be 
displayed. If not, remove batteries for 10 seconds and reinstall. If the outdoor temperature is not 
displayed within four minutes, remove batteries from both units, wait 30 seconds, and reinstall 
making sure to install batteries into the remote temperature sensor first. The time will show 
12:00 and start searching for the WWVB signal. If it successfully receives the time signal 
(usually at night), it will display the correct time (default time-zone is Eastern). You will need to 
adjust the time zone to match your local time.  

 

PROGRAM MODE 

 

Programming Note:

 If 15 seconds are allowed to pass, or the 

SNOOZE/CH

 button is pressed during the 

programming mode, the unit will confirm/set the last information entered—the display will stop flashing 
and return to normal time-date readings. If you don’t leave the program mode during the programming of 
sections IV through XI, you can advance to step 4 of the next program setting. If you do leave the program 
setting (or want to program a specific setting) follow each instructional step to program that setting. 

 

I.

 

PROGRAMMING SEQUENCE AND DEFAULT SETTINGS                     

 

The programming sequence and default (factory) settings are as follows: 

 

LCD Contrast 

Time Zone 

-5 (Eastern) 

Daylight Saving Time 

ON 

Radio-controlled time 
reception 

ON 

12/24-hour time 

12 

Time – Hour 

12 

Time – Minute 

:00 

Year 2003 
Month 1 
Day 1 
Snooze 10 

minutes 

Forecast Sensitivity 

 

II.

 

FUNCTION KEYS

 

The function keys are located on the front of the unit directly below the LCD (Liquid Crystal 
Display). 

 
 
 
 

Summary of Contents for WS-9043U




















Reviews: