background image

 

16

 
Common to weather forecasting, absolute accuracy cannot be 
guaranteed. The weather forecasting feature is estimated to 
have an accuracy level of about 75% due to the varying areas 
the projection alarm clock station has been designed for use. In 
areas that experience sudden changes in weather (for example 
from sunny to rain), the projection alarm clock will be more 
accurate compared to use in areas where the weather is 
stagnant most of the time (for example mostly sunny). 

 

If the projection alarm clock is moved to another location 
significantly higher or lower than its initial standing point (for 
example from the ground floor to the upper floors of a house), 
discard the weather forecast for the next 12-24 hours. By doing 
this, the projection alarm clock will not mistake the new location 
as being a possible change in air-pressure when really it is due 
to the slight change of altitude.  

 

2. 

WEATHER TENDENCY INDICATOR 

Working together with the weather icons is the weather tendency 
indicators (located to the right of the weather icons). When the 
indicator points upwards, it means that the air-pressure is 
increasing and the weather is expected to improve, but when 
indicator points downwards, the air-pressure is dropping and the 
weather is expected to become worse. 

 

Taking this into account, one can see how the weather has 
changed and is expected to change. For example, if the indicator 
is pointing downwards together with cloud and sun icons, then 
the last noticeable change in the weather was when it was sunny 
(the sun icon only). Therefore, the next change in the weather 
will be cloud with rain icons since the indicator is pointing 
downwards. 

 

NOTE:  

After setting up, readings for weather forecasts should be  

                disregarded for the next 12-24 hours. This will allow sufficient time   
                for the projection alarm clock to collect air pressure data at a  
                constant altitude and therefore result in a more accurate forecast. 

NOTE:

  

Once the weather tendency indicator has registered a change in air   

               pressure, it will remain permanently visualized on the LCD. 

Summary of Contents for WT-5130
























Reviews: