background image

(P/N)762.128 Rev B EN 05/10 • © copyright 2009-2010 

Kaba Mas LLC

page 1

In order to maintain the highest quality standards and ensure a problem-free application, please read this guide thoroughly before 
mounting the input unit. The installation instructions are the basis for Security Agency Approvals. The lock installation must be done in 
accordance to these instructions in order to maintain the labeled approval level.

SAFEGUARDS FOR MOUNTING 

1. Once an electronic lock has been mounted, no more welding can be done on the safe.
2. Keep metal dust, filings, etc. away from the lock.
3. Keep cables away from sharp edges and moving parts.
4. Never carry keypads or locks by the cable.
5. Use 9-Volt ALKALINE batteries only. The use of a high quality, name brand battery (Energizer® or Duracell®) is recommended.

BASIC TOOLS AND MATERIALS REQUIRED:

  •  Medium Phillips head screwdriver (#2) (recommend magnetized tip)
  •  Small flat file or deburring stone
  •  Tape measure or ruler
  •  ESD wrist band

PREPARATION FOR NEW INSTALLATION: (IF REQUIRED)

1. Use the template provided to establish the exact locations (relative to the spindle hole) of the mounting holes for the Entry Device
  and the lock assembly. Be sure to consider the cable length from the entry device to the lock.
2. The spindle hole diameter can be a minimum of .406" (10.3mm) to a maximum of .438" (11.1mm). The .406" (10.3mm) diameter is
  recommended. Spindle hole must be deburred.
3. The Entry Device mounting screws require drilled and tapped holes to 3/8" (9.5mm) depth if possible (minimum 1/4" or 6.4mm
  depth required.) Drill either the two horizontal mounting holes or the two vertical holes.

For Lock installation instructions, refer to 717.088 available at www.kaba-mas.com.

ELECTRONIC

ENTRY DEVICE

Installation Instructions

GENERAL INFORMATION

Summary of Contents for 3000














Reviews: