background image

(P/N) 742.049 Rev A 06/10 • © copyright 2010 

 

 

Kaba Mas LLC

page 2 of 13

LOCK OPERATING CONVENTIONS 

Without eKEY 

•  If a mistake is made while entering keystrokes, wait thirty (30) seconds and repeat operation. 
•  To access lock commands, enter combination and hold down the last digit until Lock double signals and the LED stays on. 
•  In Dual Mode, two combinations are required to operate the Lock. 

NOTE: 

In Dual Mode, a valid User combination must be entered first, followed by the Manager combination, to access the 

following Manager Commands: 1, 2, 3, 7 and 9.

•  Lock must be opened within 4 seconds once a valid combination has been entered. 
•  To open a container with a Swing Bolt Lock, turn the container handle to the open position and open the door. 
•  To open a container with a Dead or Spring Bolt Lock, turn the keypad or dial to retract the bolt and open the door. 
•  When closing a container, verify that it has been secured. 

With eKEY(Dual Token)
NOTE: 

Locks must be factory programmed with this feature enabled. The eKEY is a 48-bit encrypted unique serial number dual 

token device. 

• To open the Lock, enter combination, insert and quickly remove the eKEY. The Lock will open after the eKEY is removed.
• To access Lock commands, enter combination and insert the ekEY until Lock double signals and the LED stays on. 

LOCK RESPONSES 

Standard Operations

Entry Devices with LEDs (3125, 3190 and 3750-K) respond with both LED flashes and beeps. 
•  Single signal - one (1) LED flash and one (1) beep indicate the operation is complete. 
•  Double signal - two (2) LED flashes and two (2) beeps indicate entry is valid or accepted. 
•  Triple signal - three (3) LED flashes and three (3) beeps indicate invalid or not accepted. 

NOTE: 

The 8130 Entry Device (no LED) responds with beeps only. 

Additional Operations

•  Delay Period - The LED will flash once every second.  
•  Open Period - The LED will flash twice a second, and the Entry Device will beep every 10 seconds.  
•  Penalty Period - The LED will flash every ten (10) seconds.  
•  Low Battery Warning - During a Lock opening, the LED will flash and Entry Device will beep repeatedly.  

Summary of Contents for AuditGard














Reviews: