background image

(P/N) 731.018 Rev H 12/14 • © copyright 2008-2014   

 

Kaba Mas LLC

page 6 of 11

Select Time Delay: 
The Delay and Open Periods may be set up in this window. Enable feature by placing a check mark in the Time Delay On box. Then 
enter the desired time period in the text box or use the up and down arrows to select the time periods. 
Example: 15 min Delay Period and 5 min Open Period  (Figure 8).
  •  A Delay period between 1 - 99 minutes may be selected.
  •  An Open period between 1 - 19 minutes may be selected.

NOTE: If Time Delay On is not selected, this feature is inactive. This feature may be enabled later by the Manager. (Refer to 
ComboGard Pro Manager Instructions 732.018.)

Figure 6

Figure 7

Figure 8

Install Users: 
The Manager cannot be disabled because the Manager must be installed with a combination in order to activate the lock. 
To install a User, place a check mark in the 

Installed box next to the User ID. When a User is selected, the default is w/Combination

The default combination can be changed by clicking in the text box and entering an alternate combination (Figure 9). When the 

w/

Combination box is unchecked, the User is available but must be enabled by the Manager later. (Refer to ComboGard Pro Manager 
Instructions 732.018.) 

Summary of Contents for ComboGard Pro 39E












Reviews: