La Gard SmartPoint Operating Instructions Manual Download

Page: 10 / 11

(P/N)702.087 v1 • 8/08

Kaba Mas LLC

page 10 of 11

2.8.8 MASTER MEnU - USER - Re-Enroll Fingerprint

1. Press any key to power up SMARTPOINT.
    •  Display will show either “ENTER CODE” or “SELECT LOCK” when two or more locks are installed.
2. Hold down “zero” until the display shows “MASTER CODE, X-X-X-X-X-X-X-X”.
3. Enter master code.
    •  If a valid code is entered the display will show “TIME/DATE”
4. Press P six (6) times to select the User Menu, the display will show “USERS ON/OFF? “.
5. Press OK to view the User status, the display will show “USERS ON/OFF, (XX - XX)”
6. Press User ID (XX) to select a user, display will show “USER ID = X, DISABLE?”
7. Press P five (5) times, display will show “USER ID = X, RE-ENROLL?”
8. Press OK, display will show “FINGERPRINT NUMBER = 1”.
9. Press OK, the display will show, “SCAN YOUR FINGER” then “2nd SCANNING” then “3rd SCANNING”. Once
  scanning is completed, the display will show “ANOTHER FINGER”.
    •  The system offers the option of scanning up to three (3) fingers for each User or the Manager.
    •  Finger should be lifted after each scan and then quickly replaced so that three separate scans are made.
    •  Repeat this procedure for each fingerprint to be enrolled for this User. The system will only ask for the number
      of fingerprints as setup during Logic Module setup.
9. Press OK to confirm and enroll another Fingerprint or P to exit, display will show “FINGERPRINT, SUCCESS”.

nOTE:

If fingerprint enrollment fails, either because the finger was not placed on the scanner fully thereby not

allowing enough information to be collected, or because the finger was either too dry or too wet for scanning,
the display will show “FINGERPRINT ENROLL FAIL” and then “TRY AGAIN?” Press OK to attempt fingerprint
enroll again.

Once the third fingerprint has been enrolled, the display will show “DURESS?”. Press OK to accept as duress or P to
bypass. If selected this fingerprint may be used to active the silent alarm signal, if this feature was set-up and if the
unit is hooked up to an external alarm system.

2.9 MASTER MEnU - Time Delay

1. Press any key to power up SMARTPOINT.
    •  Display will show either “ENTER CODE” or “SELECT LOCK” when two or more locks are installed.
2. Hold down “zero” until the display shows “MASTER CODE, X-X-X-X-X-X-X-X”
3. Enter master code.
    •  If a valid code is entered the display will show “TIME/DATE”
4. Press P seven (7) times to select the TIme Delay Menu, the display will show “TIME DELAY”
5. Press OK to enter the Time Menu, the display will show “TIME DELAY, TD:XX OW:XX” when only one lock is
  installed or “SELECT LOCK, 1 - - - -” when more than one lock is enrolled.
6. Enter new values for the Time Delay and Open Window, display will show “TIME DELAY SET OK!”
    •  If the lock is already set for Time Delay, the unit will begin counting through the current Delay time. If the new
      Delay time is less than the existing Delay time, the system must go through the entire sequence before the
      new Delay time takes effect.
    •  To delete Time Delay enter 00 for the Time Delay time and 01 for the Open Window.

2.10 MASTER MEnU - Open Offset

This function is used if an extended period of time is required between entering a valid code and
lock activation.

nOTE:

Offset can be set between 1 and 99 seconds.

CAUTIOn: THE OPEn OFFSET TIME IS PART OF THE OPEn WInDOW TIME. THE OPEn OFFSET TIME MUST BE LESS THAn THE
OPEn WInDOW TIME.

MASTER CODE

XXXXXXXX

MASTER CODE

XXXXXXXX

MASTER CODE

XXXXXXXX

TIME/DATE