31
If it becomes difficult to open or close a valve, do not force it, but immediately request the assistance of the
technical service personnel.
Cleaning the enamelled parts:
To maintain the original features of the enamelled parts they should be cleaned frequently with soapy water. Never use
abrasive powders. Do not leave acidic or alkaline substances on the enamelled parts (vinegar, lemon juice, salt, tomato
sauce, etc.) and do not wash the enamelled parts while they are still hot.
Cleaning the STAINLESS steel parts:
Clean the parts with soapy water and then dry them with a soft cloth. The shine is maintained by periodically using
special products that generally are found in the market. Never use abrasive powders.
Cleaning the burner flame caps:
Since the flame caps are resting on the burner, to clean them just remove them from their seat and wash them with
soapy water. After they have been thoroughly dried and having checked that the holes are not clogged, they can be
replaced in their proper position.
Oven door with glass screwed:
Cleaning the inside of the oven glass:
One of the features of the oven is the possibility of removing the interior glass simply by loosening the 2 screws
B
(fig.
44-45), to clean the inside surface of the glass. This operation should be carried out while the oven is cold and with a
damp cloth. Do not use abrasives.
Cleaning the inside of the oven:
To thoroughly clean the inside of the oven, it is recommended to disassemble the door by carefully following the
instructions described below. Insert the hook
C
(figure 46) into the hinged sector
D
. Put the door in a semi-open position
and using both hands pull it towards you until it is released from the attachment. To replace the door, do the opposite
making sure to insert the two sectors
F
correctly. In addition, the side shelves can be removed very easily, by loosening
the lock rings that attach them to the oven.
Oven door with glass stuck:
Cleaning the inside of the oven glass:
Cleaning the interior of the crystals of the oven:
Feature of the oven is the ability to remove the inner glass in order to make the internal cleanliness of crystals. This
operation is to be performed in a cold oven and with a damp cloth, taking care not to use abrasive detergents. For the
removal of internal glass lock the hinges by inserting the nail that came in the hinges (22 Fig 47-48) then remove the
inner glass as (Fig.49-50-51-52-53-54)..
To reassemble the door to perform tasks in the opposite direction as (fig.55-56-57-58).
Cleaning the inside of the oven:
To facilitate intensive cleaning of the oven is practical to dismantle the door by following the instructions listed below.
Insert the nail that came in the hinges (Fig. 47-48). Bring the half-open door in place and working with your hands pull the
door towards you until the same has not been dropped from the attack. To replace the oven door proceed in reverse
order. Also the grids side are easily-removable by unscrewing the rings that secure it to the oven.
AFTER-SALES TECHNICAL SERVICE AND SPARE PARTS
Before leaving the factory, this appliance was tested and calibrated by skilled and qualified personnel.
Any repairs or calibration that may become necessary after leaving the factory should be performed by skilled personnel.
For this reason we advise the customer to contact the Dealer that sold the appliance or the nearest Service Centre,
providing them with information about the type of appliance and the type of problem that has occurred.
If defective parts must be replaced, it is recommended to replace them with original spare parts that are available only in
our technical Service Centres and authorised dealers.
Summary of Contents for AMN855GXV
Page 47: ...47 Fig 1 Fig 2 Fig 3 Fig 4 Fig 5 Fig 6 Fig 7 Fig 8 Fig 9 Fig 10 Fig 11 Fig 12...
Page 48: ...48 Fig 13 Fig 14 Fig 15 T Fig 16 Fig 17 Fig 19 Fig 20 Fig 21 Fig 22 Fig 23 Fig 24...
Page 50: ...50 Fig 41 Fig 42 Fig 43 Fig 44 Fig 45 Fig 46 Fig 47 Fig 48 Fig 49 Fig 50...
