5
specialist. In the event of a damage that occurs as a result of
improper connection, the warranty will be void.
❍
Our appliances meet the applicable safety regulations for
electrical appliances, Repairs may be performed only by
customer service engineers trained by the manufacturer.
Inexpert repairs may entail serious injury to you, the user.
Safety considerations
❍
Never leave the appliance unattended when cooking with fat
or oil. It could ignite if overheated.
❍
In case of a defect, switch off at the mains.
❍
Do not clean the oven with steam or high pressure cleaners.
❍
Ensure that the power cord does not get caught in the hot
oven door. The plastic insulation could melt.
❍
Do not use loose greaseproof paper in the oven (e.g. when
heating the oven). The paper could be drawn to the fan and
damage the fan and the element.
❍
Do not insert a baking sheet or aluminium foil sheet at the
bottom of the oven. A heat build-up could result and cooking
times and temperatures could change or enamel could be
damaged.
❍
Do not pour water on the hot oven floor. Damage to enamel
could result.
❍
Always place a baking tray below a roast to prevent juices
from dripping on the oven lining.
❍
Do not place heavy items on the oven door when open as this
may result in damage to the door hinges.
❍
To ensure correct cooking the oven door must close properly.
Keep the door sealing surfaces clean at all times.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
WHERE THIS APPLIANCE IS INSTALLED IN A MARINE CRAFT OR IN
CARAVANS, FOR SAFETY REASONS IT SHALL NOT BE USED AS A
SPACE HEATER.
THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN
OR INFIRM PERSONS WITHOUT SUPERVISION. YOUNG CHILDREN
SHOULD BE SUPERVISED TO ENSURE THEY DO NOT PLAY WITH THIS
APPLIANCE.
WARNING - ACCESSIBLE PARTS WILL BECOME HOT WHEN IN USE.
TO AVOID BURNS OR SCALDS CHILDREN SHOULD BE KEPT AWAY.
32
8. Ensure that both hinge levers are placed in the upwards
position and relocate the hinges into the oven frame. Swing
the levers back to the horizontal position and close the door.
To replace oven fan
Pull cooker forwards to gain access to the rear of the cooker.
1. From inside the oven compartment remove the fan cover plate
by removing 5 phillips head screws.
2. Using a 10mm spanner remove the central dome nut securing
the fan to the spindle.
3. Remove the cooker rear cover by removing 7 phillips head
screws.
4. Disconnect electric wiring and earth wire from fan motor.
5. Remove the 3 motor retaining screws.
6. Replace the fan assembly and reconnect wiring.
7. Reassemble in reverse order.
To replace the electronic programmer
Follow procedure described as per the heading ‘To replace the
gas control valves and gas manifold’.
1. Undo electronic connectors. Mark connectors to ensure
correct reconnection positions.
2. Slide electronic programmer forwards to remove and replace.
3. Reconnect electronic connectors.
4. Replace in reverse order.
To replace element from around the oven fan
Pull cooker forwards to gain access to the rear of the cooker.
1. Remove cooker rear cover by unscrewing 7 phillips head
screws.
2. Disconnect electric wiring to the element at the rear of the
oven.
3. Undo 2 phillips head retaining screws securing the element
at the rear of the oven.
4. Remove the thermostat bulb from its clips at the top of the fan
cover.
5. From inside the oven compartment remove the fan cover plate
by removing 5 phillips head screws.
6. Replace element and reconnect wiring.
7. Reassemble in reverse order.
To replace top element
Pull cooker forwards to gain access to the rear of the cooker.
Summary of Contents for LUEP51-90-S
Page 35: ...Part no W1885 Revision D 2006...
