background image

Installation, Operation and Maintenance Instructions

Document 2108A

Installation,

Operation and

Maintenance

Instructions for

9600 HWG

Condensing Water

Heater for Natural Gas

or Propane

Models

HWG-M2-150

HWG-M2-175

HWG-M2-200

HWG-M2-250

FOR YOUR SAFETY:

 This product must be installed and serviced by a professional service technician,

qualified in hot water heater installation and maintenance. Improper installation and/or operation could

create carbon monoxide gas in flue gases which could cause serious injury, property damage, or death.

Improper installation and/or operation will void the warranty.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flamable vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department .

• Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

10-427A

Summary of Contents for HWG-M2-150





















Reviews: