Laars Pennant PNCP, Installation And Operation Instructions Manual

LAARS Heating Systems

Page 14

By depressing the upper left hand button at any

time during the programming, the menu may be
returned to the beginning.

5.3.3 Setpoint - LSP

The setpoint is the desired temperature around

which the heater will control (desired pool
temperature). It is adjustable between 60° F and
104° F.

5.3.4 Differential - dLS

The differential (dLS) is the number of degrees

between the temperature at which the heater turns off
and the temperature at which the heater restarts. It is
adjustable from 2° F to 10° F.

5.3.5 Pump Operation

The pump is energized whenever there is a heat

demand.

5.3.6 Heater Purge (Pump Delay) - Pd

After a demand is satisfied, the pump will

continue to run for a preset length of time. That length
of time is adjustable from 0.1 to 10 minutes and is
programmed by the parameter Pd.

Caution

Should overheating occur or the gas supply fail to
shut off, turn off the manual gas control valve to the
appliance.

5.4 Limit Controls

In addition to the pool heater temperature

control, Pennant appliances are fitted with a Pool
Loop high limit set at 135° F and an automatic reset
heater high limit with a maximum setting of 190° F.

The Pool Loop high-limit sensing bulb is to be

installed in the sensor well (supplied), downstream of
the heater (see Figure 5). If sufficient capillary length
exists to reach the sensor location, the control may
remain in its location near the rear of the cabinet on
the right side, behind the slide out drawer (see Figure
8). If the sensor location is farther from the heater than
the capillary will reach to, then the control should be
moved to the remote location and the wires extended
to the new location of the control. If the controller
needs to be moved, and it is being moved to an
outdoor location, the control will need to be put in a
weather-tight enclosure to protect it from rain, snow,
etc.

The other limit control limits the temperature of

the discharge from the heat exchanger to a maximum
of  190° F. This limit should be set to a minimum of
175° F. To set the limit controls, remove the control
panel cover and pull the control panel out to gain
access. Appliances with reversed heat exchangers have
the limit controls relocated to the left side of the
appliance. The left access door must be removed to
gain access to the limit controls on these appliances.

SECTION 6.
Operating Instructions

6.1 Sequence of Operation

The amber “Ready” light on the front panel

indicates that the control system is energized. Upon a
call for heat from the pool temperature control, the
green “Heat” indicator on the front panel will light.

The green “Pump” indicator on the front panel

will light.

Once the water flow switch makes, and if all of

the safety interlocks are closed, the ignition module(s)
will energize the blower(s) for a 15-second pre-purge,
followed by a 20-second period to allow the ignitor(s)
to heat.

Energizing the blower pressurizes the air box

(which supplies air to the burners) and closes the
normally-open contact(s) of the airflow pressure
switch(es). This allows the ignition module to proceed
with the ignition sequence.

The blocked flue pressure switch senses the

pressure difference between the exhaust plenum and
the blower inlet plenum. It will interrupt the airflow
sensing circuit if this pressure exceeds a maximum
value. If airflow is not proven, the ignition module
will either attempt ignition again (up to three times) or
will lockout (if the optional lockout ignition module is
used).

The ignition module checks that the ignitor

current has reached a minimum value and energizes
the gas valves at the end of the ignitor-heating period.
The green indicators on the front panel will light,
indicating that the gas valves are open.

After a 4-second trial for ignition, the ignitor

switches off, and unless the flame sensor detects a
flame, the gas valves will close and the ignition
module will either attempt ignition again (up to three
times) or will lockout (if the optional lockout ignition
module is used). Note: at this point, if gas pressure is
below the required 5" w.c. minimum, the pool heater
will lock out.

If flame is sensed, the burner will continue to fire

as long as there is a call for heat. Pennant 1250, 1500,
1750 and 2000 models start at part load. When the gas
valves controlled by the first ignition module are
energized, the second ignition module is energized and
enters the same ignition sequence just described. If
there is a subsequent loss of flame signal, the burner
will attempt re-ignition up to three times (only once if
optional lockout ignition module is used.) Loss of
flame signal from the first ignition module will cause
shutdown of the heater.

When the call for heat is satisfied, the gas valves

close and the blower(s) continues to run for 30
seconds. The pump will continue to run for the length
of time selected at startup by the adjustment of the
pump time delay (Pd).