background image

 

Warranty and disclaimers 

• 

General 

This product is manufactured by LAB.GRUPPEN 
and is warranted to be free from defects in 
components and factory workmanship under 
normal use and service, for a period of one year 
from the date of original purchase. 
During the warranty period, LAB.GRUPPEN or its 
nominated agents, will undertake to repair, or at its 
option, replace this product at no charge to its 
owner, when failing to perform as specified, 
provided the unit is returned undamaged and 
shipping pre-paid, to factory or authorised service 
facility. 
No other warranty is expressed or implied. 
This warranty shall be null and void, if the product 
is subjected to: 
1)  Repair work or alteration by person other than 
those authorised by LAB.GRUPPEN or its agents. 
2)  Shipping accidents, war, civil insurrection, 
misuse, abuse, operation with incorrect AC voltage, 
operation with faulty associated equipment and 
normal wear and tear. Units, on which the serial 
number has been removed or defaced, will not be 
eligible for warranty service. 
3)  LAB.GRUPPEN shall not be responsible for 
any incidental or consequential damages, with 
respect to the products warranted. 
 
LAB.GRUPPEN reserve the right to make changes 
or improvements in design or manufacturing, 
without assuming any obligation to change or 
improve products previously manufactured. 

 
 
 
 

 

• 

International 

Please contact your supplier for this information, as 
rights and disclaimers may vary from country to 
country. 

 

Technical assistance and services 

• 

International 

If your LAB.GRUPPEN product needs repair, 
contact your LAB.GRUPPEN dealer or distributor, 
or contact LAB.GRUPPEN by fax, to obtain the 
location of the nearest authorised service centre. 

 

• 

Factory services

 

In the event that your LAB.GRUPPEN product 
needs factory service, you shall contact 
LAB.GRUPPEN service department for return 
instructions and a Return Authorisation number.  

Please note on product return:

 

1.  Use the original packing 
2.  Include a copy of the sales receipt, your name, 

return address, phone number, fax number and 
defect description. 

3.  Mark the Return Authorisation number on the 

outside of the packing. 

4.  Ship the product prepaid to: 
 

LAB.GRUPPEN 

  Gullregnsvägen 

16 

  434 

44 

Kungsbacka 

  SWEDEN 
 
Telephone:   

+46 300 562800 

Fax 

  +46 

300 

562899 

 

 

12

Summary of Contents for LAB 1300C













Reviews: