background image

 

3

 

Lab Research Products PRODUCT WARRANTY 

 
Lab Research Products warrants to the original purchaser every new Lab Research Products 
refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship, 
under normal use and service, for a period of two (2) years.  The warranty period starts two weeks from 
the date of shipment from Lab Research Products.  This two-week period allows ample shipping time so 
that the warranty will go into effect at approximately the same time your equipment is delivered.  Unless 
subject to prior written agreement with Lab Research Products, this warranty does not allow for any 
warranty start deferment greater than two weeks from date of shipment due to a delayed installation 
and/or start-up. 

 

Under this warranty, Lab Research Products, through its authorized service organizations, will repair, or 
at its option, replace any part found to contain a manufacturing defect in material or workmanship without 
charge to the owner for parts, service labor or any shipping or cartage costs.  Replacement or repaired 
parts will be warranted for only the unexpired portion of the original warranty. 
 

 

ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY 

 

In addition to the two (2) year warranty stated above, Lab Research Products warrants its hermetically 
and semi-hermetically sealed compressors to be free from defects in both material and workmanship 
under normal use and service for a period of three (3) additional years from the end of the initial two (2) 
year warranty period, but not to exceed five (5) years after shipment from Lab Research Products

 

Compressors determined by Lab Research Products to have been defective within this extended time 
period will, at Lab Research Products' option, be either repaired or replaced with a compressor or 
compressor parts of similar design and capacity.   

 

The three (3) year extended compressor warranty applies only to hermetically and semi-hermetically 
sealed parts of the compressor and does not apply to any other parts or components, including, but not 
limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor starting 
equipment, fan assembly or any other electrical components. 

 

Lab Research Products' sole obligation under this warranty is limited to either repair or replacement of 
parts, subject to the additional limitations below.  This warranty neither assumes nor authorizes any 
person to assume obligations other than expressly covered by this warranty. 

 

NO CONSEQUENTIAL DAMAGES.  Lab Research Products is not responsible for economic loss; profit 
loss; or special, indirect or consequential damages, including without limitation, losses or damages arising 
from contents spoilage claims whether or not on account of refrigeration failure. 

 

WARRANTY IS NOT TRANSFERABLE.  This warranty is not assignable and applies only in favor of the 
original purchaser/user to whom delivered.  Any such assignment or transfer shall void the warranties 
herein made and shall void all warranties, express or implied, including any warranty of merchantability or 
fitness for a particular purpose. 

 

NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
There are no other warranties, express, implied, or statutory, except the two (2) year warranty and the 
additional three (3) year compressor warranty as described above.  These warranties are exclusive and in 
lieu of all other warranties, including implied warranty and merchantability or fitness for a particular 
purpose.  There are no warranties, which extend beyond the description on the face hereof. 

 

ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR 
INSTALLATION, FIRE, FLOOD OR OTHER EXTERNAL CAUSES.
   
Lab Research Products is not responsible for the repair or replacement of any parts that Lab Research 
Products
 determines have been subjected after the date of manufacture to alteration, neglect, abuse, 
misuse, accident, damage during transit or installation, fire, flood or other external causes.  It does not 
apply to defects resulting from failure to properly install, operate or maintain the product in accordance 
with the printed instructions provided, or damage caused by the storage of any corrosive material that 
comes in contact with the interior or exterior portions of the cabinet, or the use of spark producing 
equipment or containers (such as galvanized or carbonized steel containers) that come in contact with 
any interior portion of the cabinet. 
 
 
 

 

Summary of Contents for MCFB-2020









Reviews: