background image

5

6

Muting the Alarm

To mute the alarm, wait until the controller is showing the 

to1H

 high alarm screen and touch 

the mute icon/button. The 

to1H

 high alarm screen will then flash to confirm you have muted 

it and the alarm will stop sounding. Repeat for the 

to2H 

alarm. 

Muting the alarm does not mean the alarm is cancelled and it will sound again after 15 minutes. 

This is the default setting which you can change using the refrigerators menu. However, the 

alarm will only cancel completely when the controller detects that the refrigerator is no longer 

in an alarm state.

To change the interval between muting and the alarm sounding again please see section 

Alarm Time Out

 page 8. 

 

After 30 seconds the icons/buttons will disappear from the front of the controller and it will 

display the temperature alternately with any active alarms. To activate the icons/buttons again, 

put your hand across the controller and they will become active after 2 seconds of appearing.

When adjusted, hold the tick icon/button until the display changes to  show the temperature 

inside the refrigerator. The red alarm light will display because the inside of the refrigerator 

hasn’t had time to cool down yet and after a few seconds the controller will alternate the 

temperature screen with a 

to1H

 and 

to2H 

high alarm screen. The alarm will sound when this 

screen is displayed.

After setting the month you next need to set the day. The controller will now flash 

d

 followed 

by 2 digits, for example 

d98

. Adjust the digits using the arrow icons/buttons as above, so if it is 

21

st 

June adjust the digits to 

21

. When adjusted, touch the tick icon/button as before.

H/L

P

H/L

P

After setting the day you next need to set the hour. The controller has a 24 hour clock and will 

now flash 

followed by 2 digits, for example 

d98

. Adjust the digits using the arrow icons as 

above, so if it is 2 O’clock, adjust the digits to 

14

. When adjusted, touch the tick icon/button 

as before.

H/L

P

H/L

P

After setting the hour you next need to set the minutes. The controller now flash 

followed 

by 2 digits, for example 

n98

. Adjust the digits using the arrow icons/buttons as above, so if it 

is half past two, adjust the digits to 

30

H/L

P

H/L

P

°

°t

1

C

H/L

P

H/L

P

ALTHOUGH THE REFRIGERATOR WILL REACH 5

o

C  WITHIN ABOUT AN HOUR,  YOU 

SHOULD LEAVE THE FRIDGE RUNNING FOR 24 HOURS BEFORE FILLING WITH 

TEMPERATURE SENSITIVE VACCINES AND PHARMACEUTICALS.

While your refrigerator is cooling down without contents, it is a good time to set up all the 

functions you want to use on your fridge. Some functions you can only view, not change.

To enable/view functions, first you need to wake the controller menu. This is done by placing 

your hand for at least 2 seconds across the controller. This contact will make the icons/buttons 

visible. 

To access the menu, hold the two arrow icons/buttons on the right hand side of the controller 

simultaneously for at least 2 seconds.

Accessing the Menu

°

°t

1

C

H/L

P

°

°t

1

C

H/L

P

Make the icons/buttons 

visible by placing your hand across 

the controller for at least 2 seconds

Access the menu by 

holding the two arrow 

icons/buttons for at least 2 seconds

Summary of Contents for IntelliCold RLDF 19 Series
















Reviews: