54
22) NEXT-RX RADIO RECEIVER
1 - GENERAL INFORMATION
The single-channel receiver NEXT-RX is a 433.92 MHz radio receiver designed to open the automatic door NEXT using the transmitters
manufactured by Label. In Table 1 there is a list of radio transmitters produced by LABELSpa.
2 - DESIGNED USE
The receiver NEXT-RX must be coupled to the connector J4 of the logic card NEXT-L120S and it is intended to control the opening of the
automatic door in all the work programs of the automation.
WARNING:
The opening command of the automatic door is issued by the radio control, but movement protection and safety are delegated to organs
other than the receiver.
It shall never be used in any case where the door activation or deactivation may cause injuries and damage. Receiver in class 3
according to the standards ETSI EN 300-220-2 V.3.1.1 (2016-11).
3 - INSTALLATION OF THE RECEIVER
Plug the cable of the receiver NEXT-RX (fig. 1) in the connector J4 of the logic card NEXT-L120S of the automation (fig. 2). Proceed with
saving the radio-controls (fig.3) as follows:
a) Enter the programming mode of the transmitters pressing and holding the button SW1 until the led L1
is steadily lit (approx. 3
seconds).
b) Press the button of the transmitter to be saved. Successful saving will be indicated by 5 fast flashings of the led L1
.
c) Then LED L1 will turn on steadily again and it will be possible to save another transmitter by repeating the operation described in
point b), and so forth for all the transmitters to be used.
•
A maximum of 250 transmitters can be saved on the receiver.
d) Once the transmitter saving procedure is finished, exit the programming mode by pressing and holding the button SW1 until the led
L1 (
) turns off.
4 - USE OF THE RADIO CONTROL
By pressing the button of a saved transmitter, the automatic door opens and the led L1 of the receiver remains on until the button of the
transmitter is released.
The radio control opens the door in all the operating programs of the automation.
5 - RECEIVER MEMORY ERASURE
Should it be necessary to erase all the transmitter codes saved in the memory of the receiver NEXT‑RX, proceed as follows:
a) Disconnect the cable from the receiver NEXT-RX from the connector J4 of the logic card NEXT.
b) Press and hold the button SW1 of the receiver and at the same time connect the cable of the receiver NEXT/RX in the connector J4
connector of the logic card NEXT-L120S.
c) Release the button SW1 of the receiver NEXT-RX only after the LED L1 of the receiver starts flashing.
Now the LED L1 of NEXT/RX blinks fast
to indicate that the receiver is ready to save the codes of all the transmitters of the
LABEL range, both rolling code models and dip switch models.
If you only wish to save the rolling code transmitters (SPYCO model), excluding all dip switch models, briefly push the SW1 button;
the led L1 blinks slowly
to indicate that the receiver is ready to save only the SPYCO transmitter codes.
To switch from one mode to the other, press the button SW1.
d) After selecting the desired mode, press and hold the button SW1 for about 3 seconds until the led L1
begins blinking very fast for
about 8 seconds, signalling that the receiver memory is being erased.
e) When the memory of the receiver NEXT-RX has been erased, the LED L1 will turn off.
f) Now it is possible to save again the code of the transmitters to be used, following the procedure described in paragraph 3.
6 - TECHNICAL SPECIFICATIONS
Power supply
12Vdc
Power draw
10mA at rest ‑ 50mA in operation
Outputs
OPEN COLLECTOR
Frequency
433.92 Mhz
Memory Capacity
250 users
Range without obstacles
30 meters
Operating temperature
-20° / +55°
Receiver class (ETSI EN 300‑220‑1 Chapter 4.1.1)
Class 3
7 - DECLARATIONS
Marketing, sale and use are valid without restrictions in all EU countries.
With this document Label SpA declares that the receiver NEXT‑RX complies with all the essential requirements and with all other
relevant provisions established by the directive RED 2014/53/EC.
The declaration of conformity is annexed to the instructions of the receiver NEXT-RX.
