background image

Only for the Single version

10. Bass

Adjusts the low-frequency tone for both 

channels.

11. Middle

Adjusts  the  middle-frequency tone  for 
both channels.

12. Treble

Adjusts   the   high-frequency   tone   for 

both channels.

        

HINT:  

Set all the potentiometers in a 

12.00   o’clock   position,   then   adjust 

them   individually   to   get   the   best 
sound. Remember, that the frequencies 

of each controller  are  related  to  each 
other, the change of one influences the 

others.

13. EQ Mod

Shift   of   equalizer’s   band   for   both 
channels.

HINT: 

Provides various EQ frequencies 

for both positions of the switch. It 

results in a shift of frequencies of the 
Middle filter and a change in low tones. 

In both settings of the 

EQ Mod,

 you get 

an entirely different sound of the 

amplifier and various EQ functions. 
The most radical change of sound may 

be obtained especially in a less  

Middle 

knob setting.

Only for the Twin version

14. Bass

Adjusts the low-frequency tone for the 

clean channel.

15. Middle

Adjusts  the  middle-frequency tone  for 

the clean channel.

16. Treble

Adjusts the high-frequency tone for the 
clean channel.

HINT:  

Set all the potentiometers in a 

12.00   o’clock   position,   then   adjust 
them   individually   to   get   the   best 

sound. Remember, that the frequencies 
of each  controller  are  related  to  each 

other, the change of one influences the 
others.

17. Bass

Adjusts the low-frequency tone for the 

distorted channel.

18. Middle

Adjusts  the  middle-frequency  tone for 
the distorted channel.

19. Treble

Adjusts   the   high-frequency   tone   for 

distorted channel.

HINT:  

Set all the potentiometers in a 

12.00   o’clock   position,   then   adjust 

them   individually   to   get   the   best 
sound. Remember, that the frequencies 

of each  controller  are  related  to  each 
other, the change of one influences the 

others.

20. EQ Mod

Shift of equalizer’s band for the clean 
channel.

21. EQ Mod

Shift   of   equalizer’s   band   for   the 

distorted channel.

HINT:

 

Provides   various   EQ 

frequencies for both positions of the 

switch.   It   results   in   a   shift   of 
frequencies of the Middle filter and a 

change in low tones. In both settings 
of   the  

EQ   Mod,

  you   get   an   entirely 

different   sound   of   the   amplifier   and 
various EQ functions.

Page 

10

Summary of Contents for AD 5202TA Twin





















Reviews: