background image

 

 

 

Resistance thermometer clamp-on technology 

for temperature measurement on pipes,  

Type series GA261x 

 

 

 

LABOM Mess- und Regeltechnik GmbH   Im Gewerbepark 13   27798 Hude   Germany 

BA_049_2019-06_10.00 

Hotline: +49 4408 804-444   Fax: +49 4408 804-100   e-mail: sales@labom.com   www.labom.com 

Page 1/6 

Operating Instructions 

 

1

 

General Information....................................................................................................... 2

 

1.1

 

General Safety Notes .............................................................................................. 2

 

1.2

 

Intended Use ........................................................................................................... 2

 

1.3

 

Conformity with EU Regulations .............................................................................. 2

 

1.4

 

ATEX Approval ........................................................................................................ 2

 

2

 

Transportation and Storage .......................................................................................... 2

 

3

 

Installation and Commissioning .................................................................................. 2

 

3.1

 

Mechanical Installation ............................................................................................ 2

 

3.2

 

Electrical Connection .............................................................................................. 5

 

4

 

Operation ........................................................................................................................ 6

 

4.1

 

Calibration ............................................................................................................... 6

 

4.2

 

Maintenance / Service ............................................................................................. 6

 

5

 

Disassembly ................................................................................................................... 6

 

 

Summary of Contents for GA261 Series







Reviews: