background image

 

INSTALLATION  

 
UNCRATING

  

 

Move the unit as close to the final location as possible before unpacking. Remove from the 

box and the styrofoam base. The location should be as close as possible to the power outlet 
so  an  extension  cord  is not needed.  This unit  requires a 

minimum  of 4 inches  of  air  flow 

space in back and 3 inches on the sides and top.

  Do not store material on the top of this 

unit.  

 

LEVELING  

You can level your unit with the screw-type adjustable leveling legs on the front corners of 
the unit.  Turn counterclockwise to raise the corner; turn clockwise to lower it. Leveling legs 
are  required  in  front  only.    Unit  may  have  a  slight  tilt  from  front  to  back  after  legs  are 
installed.  This is acceptable and is recommended on this unit. 
 

POWER SOURCE  

The  supply  circuit  to  this  cabinet 
must  conform  to  all  National  and 
Local Electrical Codes.  Consult the 
cabinet  Serial-Data  plate  for 
voltage,  cycle,  phase,  and  amp 
requirements 

before 

making 

connection.      VOLTAGE  SHOULD 
NOT  VARY  MORE  THAN  5%  FROM 
SERIAL  PLATE  RATINGS.    A  separate  circuit  is 
recommended  to  prevent  possible  loss  of  product 
due  to  over-loading  or  failure  of  other  equipment 
on the same circuit.  PROTECT THE CIRCUIT WITH A 
20  AMP  DELAY-TYPE  FUSE  OR  CIRCUIT  BREAKER.  
Do not use an extension cord.  Be sure your unit is 
properly grounded.  Use the 3-prong plug provided 
into  a  3-prong  grounded  outlet.  (Only  this  method 
complies with national electrical codes, local codes 
and  ordinances.)    Unless  the  above  grounding 
method  is  followed,  you  are  not  protected  against 
severe or lethal shock in the event of a short circuit 
of an electrical component or wiring of the unit. 

Summary of Contents for LABH-2-FM












Reviews: