background image

USER’S MANUAL

INDUCTION HOB

  Never place or leave enamelled, aluminium or any other type of empty pan on a heating zone. 

Similarly you should not place aluminium-packed products/ tin fail directly on the surface; this can do 

irreparable damage to your cooker. 

  Do not place unopened tins directly on a hotplate as this could cause them to explode under 

pressure. 

  Never obstruct ventilation zones (front panel, rear ventilation, etc.). The cooker may overheat and 

become less efficient. Furthermore you shorten the service life of your hob.

  Do not store aerosols or flammable products under the cooking surface.

Use a magnet to check that your pans are ferromagnetic. If they stick to the magnet, you can use 

them on induction hotplates.

Do not hang heavy items over the cooking surface. They can damage the vitro-ceramic surface if 

they fall.

Never apply more heat than can be absorbed by the food: too much heat causes loss of water, 

grease and wastes energy.

Whenever the recipe permits, cover your cookware with a lid in order to save energy.

Safety 

:

The latest scientific research has found that people fitted with a heart pacemaker are not at risk from 

using induction cookers. However, if an induction cooker is used improperly a slight risk cannot be 

ruled out.
It is for this reason that we advise people with pacemakers to consult their physician before using an 

induction cooker.
Avoid all contact between jewellery (rings, chains, etc. ) and the cooking surface while it is switched 

on; it could cause jewellery to heat.

CAUTION 

:

If a visible crack appears in the vitro-ceramic surface of your hob, immediately disconnect 

the power supply and contact your installer.

Display :

F

The sensor for a particular hotplate is not 

working

The rest of the surface can nevertheless continue functioning 

correctly 

– Contact your retailer

H

Residual temperature

Indicates that the zone is hot 

– The display goes out when the temp has dropped below 60°C

Pan undetected 

No pan or pans unsuitable for induction cooking 

U

Temperature hold : 70 °C

-

u

Temperature hold : 42 °C

-

L

Child safety function

This function is activated and deactivated by holding the knob in 

position “A”

P

Booster function 

This function is only available on hotplates A and B. .

Fault detected in the induction system

This function is activated and deactivated by holding the knob in 
position «A».
Check the control encoder connectors.
Check the connection to the encoders and inductors and for any 

damaged or cut wires 

If the induction cooker does not work

• Check your pans
• First switch off the cooker. Then check ventilation of the generator
• First switch off the cooker. Then check the power supply and electrical connectors.

Citeaux induction - Ft 158a - GB - Rév 06 - Modifié le : 07/10/2013                     26/36

Summary of Contents for CITEAUX INDUCTIONLVI 1532 E / CT





































Reviews: