background image

LACHAPELL AUDIO 500CS

SAFETY INSTRUCTIONS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS 
INSIDE. CONTACT DIGITAL AUDIO LABS FOR  SERVICING.

IMPORTANT SAFETY INSTRUCTIONS

1. 

Read and understand this entire manual.

2. 

Keep this manual available for reference.

3. 

Heed all warnings and precautions in this manual and notices marked on the product.

4. 

Do not use this product near water or damp environments.

5. 

Refer all servicing to qualified service personnel. There are no user serviceable components inside 

the product.

6. 

The product shall not be exposed to moisture. Do not touch the unit with wet hands. Do not 

handle the unit or power cord when your hands are wet or damp. 

7. 

The product should be connected to a power supply only of the type described in the operating 

instructions or as marked on the product.

CARE

• 

From time to time you should wipe off the front and side panels with a dry soft cloth. Do not use 
rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the 

finish or remove the panel lettering.

• 

The manufacturer cannot be held responsible for damages caused to persons, personal 

possessions, or data due to an improper or missing ground connection.

Summary of Contents for 500CS













Reviews: