the foldout table stand is extended, place the weather station in an appropriate
location.
POSITIONING THE THERMO-HYGRO TRANSMITTER
The Thermo-hygro transmitter is supplied with a holder that may be
attached to a wall with the three screws supplied. Before securing the
transmitter, ensure that the 433MHz signal is properly received. To attach to
the wall, please follow the steps below:
1.
Mark the wall using a pen through the holes in the holder to obtain the
exact drilling position.
2.
Drill holes in the wall at the points marked.
3.
Screw holder onto wall.
There is also double sided tape included with the wall mount. On smooth surfaces this can be used
instead of drilling holes. The mounting surface can, however, affect the transmission range. If for
example the unit is attached to a piece of metal, it may then either reduce or increase the
transmitting range. For this reason, we recommend not placing the unit on any metal surfaces or in
any position where a large metal or highly polished surface is in the immediate proximity (garage
doors, double glazing, etc.). Before securing in place, please ensure that the Weather station can
receive the 433MHz signal from the Thermo-hygro transmitter at the positions that you wish to
situate them.
The Thermo-hygro transmitter simply clicks in or out of the holder. When inserting or removing the
Thermo-hygro transmitter from the wall holder please hold both units securely.
CARE AND MAINTENANCE:
•
Extreme temperatures, vibration and shock should be avoided as these may cause damage to
the units and give inaccurate forecasts and readings.
•
When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or
scouring agents as they may mark the LCD and casings.
•
Do not submerge the units in water.
•
Immediately remove all low powered batteries to avoid leakage and damage. Replace only
with new batteries of the recommended type.
•
Do not make any repair attempts to the units. Return it to their original point of purchase for
repair by a qualified engineer. Opening and tampering with the units may invalidate their
guarantee.
•
Do not expose the units to extreme and sudden temperature changes, this may lead to rapid
changes in forecasts and readings and thereby reduce their accuracy.
SPECIFICATIONS:
Temperature measuring range:
Indoor
: -9.9ºC to +59.9ºC with 0.1°C resolution
14.2ºF to 139.8ºF with 0.2ºF resolution
(“
OF.L
” displayed if outside this range)
Outdoor
: -29.9ºC to +69.9ºC with 0.1°C resolution
-21.8ºF to +157.8ºF with 0.2ºF resolution
(“
OF.L
” displayed if outside this range)
Indoor and outdoor relative humidity range:
1% to 99% with 1% resolution
(Display “- -“ if outside this range or temperature is
OF.L
)
Interior data checking intervals
Indoor Temperature
: Every 15 seconds
Humidity
: Every 20 seconds
Air pressure checking interval : Every 15 seconds
Outdoor temperature and humidity data checking interval:
Every 5 minutes
Transmission range
: up to
100
meters (open space)
Power consumption:
(alkaline batteries recommended)
Weather station
: 3 x AA, IEC LR6, 1.5V
Thermo-hygro transmitter
:
2 x AAA, IEC LR3, 1.5V
Dimensions (L x W x H):
Weather station
:
117.4 x 31.2 x 227.1mm
Thermo-hygro transmitter
:
56 x 24 x 80 mm (excluding wall bracket)
LIABILITY DISCLAIMER
•
The manufacturer and supplier cannot accept any responsibility for any incorrect readings and
any consequences that occur should an inaccurate reading take place.
•
This product is not to be used for medical purposes or for public information.
•
This product is only designed to be used in the home as indication of the future weather and is
not 100% accurate. Weather forecasts given by this product should be taken only as an
indication and not as being totally accurate.
•
The specifications of this product may change without prior notice.
•
This product is not a toy. Keep out of the reach of children.
•
No part of this manual may be reproduced without written consent of the manufacturer.
R&TTE Directive 1999/5/EC
Summary of the Declaration of Conformity : We hereby declare that this wireless transmission device does comply
with the essential requirements of R&TTE Directive 1999/5/EC.
