background image

Fusion Tablesaw

 

 

26 

 

  

There is a 101.6 mm dust outlet located on the lower left of the saw cabinet allowing for the 

connection to a dust collection system (not included). 

Air current speed is 20m/s for vacuum suction dust emission index. When air current speed of dust collector device (in accordance with EN 
12779:2004+ A1:2009) is not lower than 20m/s, ensure machine can be normal exhausted. User must wear dustproof mask. 

1. Fit the 4" dust hose over the dust port, (not included) and secure in place with a hose clamp. 

2. Make sure the hose could not come off. 
3. Required air flow: 934 m

3

/h 

4. Ensure pressure drop of each dust collector outlet carrying air current speed: 1500Pa 

5. Wind speed of dust collector tube m/s: dry chips: 20m/s, water content is equal to18% wet chips: 28m/s. 

 
 

 
 
 
 

 

To clean wood chips 

 

 

 
 

 

Remove the side cover, to clean and remove dust, debris from dust Hood 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

PUSH Block and Push stick 

 

A push block (

Fig.2

) and A push stick (

Fig.3

) must be used

Warning:

 Always turn on the dust collector 

before starting the saw and stop the saw before 

turning off the dust collector. 

 
Note:

 A tight fit is necessary for proper performance. 

 

Warning:

 Always turn off the table saw before removing 

any cover of the machine 

 

 

 

 

 

Warning:

 Use only the push stick provided by the 

manufacturer or constructed in accordance with the 

instructions. This push stick provides sufficient distance of 

the hand from the saw blade. 

 

Warning:

 

Never use a damaged or cut push stick. A 

damaged push stick may break causing your hand to slip 

into the saw blade. 

If the workpiece is less then 120mm, you must use the push stick to 
prevent your hands from getting too close to the saw blade.  
 push block must be used to cut narrow workpieces

 

and, when necessary, 

to push the workpiece against the fence, a push block can be easily made 
by the operator as 

Fig.2

 

Summary of Contents for Fusion 2














































Reviews: