Laica HYDROSMART+ METAL STOP, Instructions And Warranty

12

13

6)  To install the connector with the 

M

 adapter, proceed as follows:

-  Remove the fastening ring from the connector and take the 

L

 adapter with Ø21 mm diameter, then assemble the 

three pieces as described in 

figure 6A, 6B and 6C

.

6A

6B

6C

-  Loosen the fastening band with a flat head screwdriver and remove the smaller seal inside the adapter 

M (fig. 

7A, 7B).

7A

7B

-  Choose the best seal: only the one with the largest diameter 

(fig. 8A) 

or both with one inserted inside the other, 

pressing firmly and taking extra care over the direction in which they are inserted

 (fig. 8B)

. 

8A

8B

-  Install the adapter 

M

 on the tap and tighten the fastening band using a flat 

head screwdriver to secure it firmly to the tap 

(fig. 9A and B)

.

-   Screw the connector onto 

the ring 

(fig. 10)

.

9A

9B

10

7)   Remove the HYDROSMART™ METAL STOP filter from its packaging and rinse it under running water. Now hook 

the filter to the connector as shown in 

figure 11A, 11B, 11C

.

11A

11B

11C

EN

Instructions and guarantee

EN

SMART FILTRATION SYSTEM – FREE LAICA HOME 

WELLNESS APP - USE

List of compatible devices:

• iOS: 

iPhone with version 10 operating system.

• For devices with Android™ operating system: 

from version 6.0 (Marshmallow).

By adding the HYDROSMART™ METAL STOP filter to 

the free “Laica Home Wellness” app, you can receive 

automatic notification on your smartphone when to 

replace the filter. 

1.  Install the free “Laica Home Wellness” app on your 

smartphone.

2.  Start the app and enter the “FILTER” section from the 

main screen.

3.  Add the HYDROSMART™ METAL STOP FILTER by 

pressing the “+” key. It is possible to add the filter by 

scanning the QR code printed on the upper part of the 

filter or manually by pressing the “Select manually” 

button.4. The app adds the filter and automatically 

prompts the replacement date. 

  To optimise the effective duration of the filter based 

on the water treated, you can select the chlorine level 

in your water supply. 

  To use it properly, request further information from your 

water supplier or carry out a preliminary assessment 

of the local water supply.

5.  Save the settings by pressing the “ ” key. 

6.  When the filter replacement date is reached, 

the notification to replace it will appear on your 

smartphone. The notification is also sent to the email 

address given during registration.

•   To scan the QR code on the upper part of the 

filter, you must authorise the app to access 

to your smartphone camera.

•  To receive notifications when to replace the 

filter, you must enable the settings on your 

smartphone.

•   To replace the filter, you can add a new one 

by scanning the QR code printed on the 

upper part of the filter or by updating the 

expiry date by clicking on the “Filter expired” 

button (click to replace)”.

USING THE FILTERING SYSTEM 

Activating the GENOVA HYDROSMART™ METAL 

STOP filter:

When first used and every time the HYDROSMART™ 

METAL STOP filter is changed, turn the tap on and allow 

the water to flow through the filter for several minutes (at 

least 4-5 minutes) to correctly activate the materials of 

which the filter is composed. This water can be used for 

watering plants. If the GENOVA filtering system has not 

been used for 24 hours or more, allow the water to flow 

for 30-60 seconds before using the filtered water again. 

CAUTION

:

-   To guarantee the performance characteristics of the 

filtering system, it is recommended to filter cold water 

only. 

-   The flow of water at a temperature higher than 50°C 

through the connector may cause permanent damage. 

The flow of water at a temperature higher than 35°C 

through the filter may cause permanent damage.

-   To adjust the water flow properly, open the tap slowly.

The GENOVA filtering system has 2 different ways of 

dispensing the water which can be selected with the 

selector 

C

:

1)  Filtered water for 

drinking, washing 

fruit and vegetables, 

cooking and carry out 

all routine tasks with 

safe, pleasant tasting 

water. 

2)  Unfiltered water with 

spray head.

REPLACING THE FILTER 

To replace the filter, turn the filter anticlockwise and 

remove it by pulling it outwards 

(fig. 12A, 12B, 12C)

.

12A

12B

12C

Replace it with a new filter repeating the steps described 

in point 7 of the paragraph “PREPARING THE FILTERING 

SYSTEM” and “USING THE FILTERING SYSTEM - Activating 

the HYDROSMART™ METAL STOP filter”. 

To achieve the best results and guarantee the safety of the 

filtering system, we recommend replacing the filter every 

4 months or 1200 litres of filtered water. 

CARE AND MAINTENANCE

Make sure your hands are clean during maintenance work 

on the filtering system. 

Regularly clean the outer part of the connector with 

a damp sponge and delicate detergent, then rinse 

thoroughly with cold drinking water. 

Do not use aggressive detergents, solvents, chemical or 

abrasive products. 

It is recommended to thoroughly clean the entire 

connector each time the filter is changed. 

For maintenance, remove the entire filtering system by 

following the installation instructions in reverse order. 

1)  Rinse the connector under unfiltered running drinking 

water.

  Do not use detergents, solvents, chemical or abrasive 

products to clean the connector. 

  If necessary, remove the fastening ring

 (E)

, the rubber 

seal

 (F)

 and rinse the stainless steel strainer 

(G) 

under 

GENOVA tap filter