background image

CL024 User Guide

 

 

Version 2.0 

 

 

 

Americas: +1-800-492-2320 Option 2 
Europe: +44-1628-858-940 
Hong Kong: +852-2923-0610 
wireless.support@lairdtech.com 

www.lairdtech.com/ramp

 

CONN-GUIDE-CL024 

 

FCC Notice  

WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference and (2) This 
device must accept any interference received, including interference that may cause 
undesired operation.  

 

RF Exposure/Installation Instructions  

WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, this 
equipment must be professionally installed such that the end user is prevented from 
replacing the antenna with a non-approved antenna. The end user should also be prevented 
from being within 20cm of the antenna during normal use with the exception of hands, 
feet, wrists and ankles.  

The preceding statement must be included as a CAUTION statement in manuals for OEM 
products to alert users on FCC RF Exposure compliance. 

Caution: Any change or modification not expressly approved by Laird could void the user’s authority to 
operate the equipment. 

 

 

Summary of Contents for CL024














Reviews: